Pumpex K 152 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 16

Pumpex K 152 Скачать руководство пользователя страница 5

5 (15)

K152/202/203/252/302.58.0101.Eng/Digital

SERVICE INSTRUCTION

K 152, 202, 203, 252, 302

Exchange of oil

Exchange of oil should be carried out if the oil is discoloured by
water or when a complete overhaul is done.

Place the motor unit on the floor or a low work bench. Loosen
the oil stick carefully to relieve over-pressure in the oil chamber.
Tighten oil stick again and loosen the oil plur, on the oil housing.
Regulate the oil flow by loosening the oil stick to allow air into
the oil chamber. Tilt the motor unit to drain all the oil from the oil
housing.

Replace the 0-rings for oil plug and oil stick and tighten the oil
plug. Fill new oil through the hole for the oil stick.

Oil type: Enerpar M002, or similar.

Oil quantity:

11-15 kW motor - 14.5 litres
23-40 kW motor - 18.5 litres

Don´t forget to tighten oil stick.

Removal of Impeller

The impeller is fitted on a cylindrical shaft end. To simplify the
loosening of the impeller bolt, place a piece of wood (pipe or
similar) inside the impeller to keep it from rotating. Loosen the
impeller bolt with a socket wrench (socket 22 mm).

The impeller has a relatively light fit on the shaft and is using a
flat key. The impeller can be removed by using two (2) pry bars
or large screwdrivers.

«
...
3
4
5
6
7
...
»

Содержание K 152

















Отзывы:

Нет отзывов