Pulsar INTRE Скачать руководство пользователя

Страница: 28 / 28

www.pulsar.pl

INTRE

6. Technical parameters.

Power supply

10 ÷ 30V DC

Current consumption

85 ÷ 30mA

TTL transmission speed

max 115200 bauds, with parity check

LAN Transmission speed

10/100Mbps (auto-sensing)

Indication (LED lights):

Tx, Rx, PWR

Operating conditions

temperature -10

C ÷ 40

relative humidity 20%...90% no condensation

Dimensions (LxWxH)

121 x 81 x 60 [mm]

Net / gross weight

0,26kg / 0,36kg

Protection class

IP65

Storage temperature

-20ºC...+60ºC

Pulsar K.Bogusz Sp.j.

Siedlec 150, 32-744 Łapczyca, Poland

Phone (+48) 14-610-19-40, Fax. (+48) 14-610-19-50

E-mail:

[email protected]

http://

www.pulsar.pl

www.zasilacze.pl

WEEE LABEL

Waste electrical and electronic equipment must not be disposed of with normal household waste. According to the European Union WEEE

Directive, waste electrical and electronic equipment should be disposed of separately from normal

household waste.

WARRANTY

5 years from the production date.

WARRANTY IS VALID only upon presentation of the original

invoice.

Содержание INTRE





























Результаты поиска

Содержание INTRE

Отзывы:

Похожие инструкции для INTRE

Бренды по названию

Популярные бренды

Pulsar INTRE, Руководство пользователя

Результаты поиска

Содержание INTRE

Отзывы:

Похожие инструкции для INTRE

Бренды по названию

Популярные бренды