Pronto MAGICARD 3649 - 0001 Скачать руководство пользователя страница 46

Страница: 46 / 90

Ultra Electronics Ltd

Pronto Maintenance Manual

- 46 -

Removal & Refitting of Rollers

Once the Bearing Plates have been removed the
Rollers can be removed out the bottom of the Printer.
Roller layout is shown below including the attached
Drive Pulleys.

Cam linkage can also be removed, but ensure both
corresponding parts are kept together to avoid
confusion when refitting.

Refitting is the reverse procedure ensuring the Cam
linkage is correctly orientated.

Removal & Refitting of the Card Guide

Remove the two return springs from either end of the Card guide. Parts of the
springs are inside the Card guide plastic assembly

The guide will be loose, push it against the internal side wall and lift up out of the
machine.

Refitting is the reverse procedure, located the Card guide and then fit the springs.

Removal & Refitting of the Middle Card Sensor

Unclip the Sensor retainer from inside the
centre of the printing compartment.

Working underneath the Printer, disconnect
the Sensor connector and withdraw the Sensor
retainer and Sensor PCB.

Refitting is the reverse procedure.

SECTION 11.16

REMOVAL AND REFITTING OF ROLLERS

SECTION 11.17

REMOVAL & REFITTING OF THE CARD GUIDE & MIDDLE CARD SENSOR

Содержание MAGICARD 3649 - 0001



























































































Результаты поиска

Содержание MAGICARD 3649 - 0001

Отзывы:

Похожие инструкции для MAGICARD 3649 - 0001

Бренды по названию

Популярные бренды

Pronto MAGICARD 3649 - 0001, Руководство по обслуживанию

Результаты поиска

Содержание MAGICARD 3649 - 0001

Отзывы:

Похожие инструкции для MAGICARD 3649 - 0001

Бренды по названию

Популярные бренды