PRONAR PT512 Скачать руководство пользователя страница 91

Страница: 91 / 139

CHAPTER 4

Pronar PT512

4.23

FIGURE 4.5

Wall and extension locks

(1) left side wall closing lever (2), rear wall closing lever (3) side wall lock (left, rear), (4) rear

wall lock (left), (5) extension lug

DANGER

Improperly secured tipping pins can cause severe damage to the trailer.

Pay particular attention when opening wall locks – the load may exert force on the trailer
walls.

When using the trailer with the second set of extensions installed, pay attention to the
trailer's stability and the increased risk of overturning. Control the trailer's movement on
uneven ground.

Ensure that during unloading nobody is near the loading case.

Due to the risk of injury, when opening/closing the bolts and the locks wear protective
gloves.

Tipping the loading case must be done only on a hard and level ground.

Exercise particular caution when operating the trailer with second set of extensions.

Use only original tipping pins with handles. Using non original pins could damage the
trailer. The tipping pins must be properly locked.

Содержание PT512












































































































































Результаты поиска

Содержание PT512

Отзывы:

Бренды по названию

Популярные бренды

PRONAR PT512, Руководство оператора

Результаты поиска

Содержание PT512

Отзывы:

Бренды по названию

Популярные бренды