PRONAR PT512 Скачать руководство пользователя страница 111

Страница: 111 / 139

CHAPTER 5

Pronar PT512

5.15

Inspection and/or adjustment of parking brake should be done:

•

every 12 months,

•

if needed.

5.3

MAINTENANCE OF PNEUMATIC SYSTEM

5.3.1 PRELIMINARY INFORMATION

Works connected with the repair, change or regeneration of system components (brake

cylinders, hoses, control valve braking force regulator etc.) should be entrusted to specialist

workshops, having the appropriate technology and qualifications for this type of work.

The user is obliged to perform following maintenance work on the pneumatic system:

•

visual inspection and control of system tightness,

•

cleaning the air filter (filters),

•

draining water from air reservoir,

•

cleaning the drain valve,

•

cleaning and maintenance of pneumatic line connectors.

DANGER

Do not use the trailer when brake system is unreliable.

5.3.2 VISUAL INSPECTION AND CONTROL OF SYSTEM TIGHTNESS

Control of pneumatic system tightness

Hitch the trailer to a tractor.

Immobilize the tractor and the trailer with parking brake. In addition, place the

chocks under the trailer's wheel.

Start the tractor in order to supplement air in trailer brake system tank.

Содержание PT512












































































































































Результаты поиска

Содержание PT512

Отзывы:

Бренды по названию

Популярные бренды

PRONAR PT512, Руководство оператора

Результаты поиска

Содержание PT512

Отзывы:

Бренды по названию

Популярные бренды