Promag WEC200 Скачать руководство пользователя страница 16

 

16 

 

Appendix A. LED2 Status 

Please see the following illustrations, LED indicates (example), 

  Represents Green and Red flash 3 times in chorus

.    As LED2 is 

dual display for 

configuration, you 

may see orange color flash 3 times visually. 

    Red LED makes one long blink followed by two short ones 

DS aims at the EM module located inside WEC200. 

 

Accordingly, please see the following patterns: 

  

Powerup pattern.

 This pattern is played once when the DS is switched on. 

 

 

Buzz pattern.

 Both LEDs blink fast. this pattern is played when the DS receives the 

Buzz (B) command

. This 

is used to identify a particular DS.    Please note that this is unrelated 6-E(BUZZER), DS is just receiving the order itself. 

(BUZZER). 

Error mode.

 

  Ethernet port failure. 

  Indicates that the Ethernet port hardware is malfunctioning and 

network communications with the DS is not possible. 

  IP-address not obtained.

 Means that the 

DHCP (DH) setting

 is 1 (enabled) and the DS has 

not yet obtained its IP-address from the DHCP server. 

  Data connection is closed.

 This pattern means that no data connection (TCP or UDP) with 

any network host is currently established. 

  Sending ARP.

 Displayed when the DS is sending ARP requests to find out the MAC-address 

of the destination network host with which the DS is about to establish a connection. 

TCP connection is being opened.

 Indicates that TCP connection (either incoming or 

outgoing) is being established (i.e. SYN-SYN-ACK exchange is in progress). 

  Data connection is established (or being closed).

 Means that data UDP "connection" or 

TCP connection is currently established or that TCP connection is being closed (i.e. FIN-ACK-FIN-ACK exchange is in 

progress). 

  Data is being routed.

 This pattern is played when the data connection is established and the 

data is being routed through the DS 

  Buffer overrun (and no data routing).

 This pattern is displayed when the data connection is 

established and the routing buffer overrun has been detected (within the present data connection). 

  Buffer o data routing.

 Data routing and overrun can be displayed at the same time. 

TCP connection reset by the network host.

 Means that the TCP connection has been reset 

(using RST packet) by the network host (not by the DS itself).

 

 

Above list shows frequent status, any details please visit Tibbo at 

http://www.tibbo.com

 

 

Содержание WEC200





















Отзывы: