Progressive Turf Equipment TDR-12 Скачать руководство пользователя | Manualshive

Страница: 20 / 70

background image

17

HITCHING MOWER TO TRACTOR

:

Attach mower to drawbar only.



Drawbar should be adjusted so it is 14” to 15” from the center line of the draw
pin hole to end of PTO shaft. This is critical for proper PTO shaft operation.



Adjust hitch or drawbar so mower frame (Item #1, Page 33) is at the most level
position in relation with the ground. This will ensure proper flotation of the
wing decks.

Safety chain must always be attached to towing vehicle.

When towing mower on any roadways, lock brakes together. Use
proper lighting and marking devices according to the local
regulations.

NOTE:

If the three-point hitch is attached to tractor, be sure it will not contact any

part of the mower when making sharp turns. Mount the hose support bracket so the
large access hole is directly over the grease fitting on the hanger bearing. The hose
support rod may have to be bent back slightly to clear the three point hitch arms.

«
...
18
19
20
21
22
...
»

Содержание TDR-12







































































Отзывы:

Нет отзывов

Похожие инструкции для TDR-12

Бренд: Agri-Fab Страницы: 32

Бренд: Ybravo Страницы: 16

Бренд: LawnMaster Страницы: 40

AMBROGIO L60 ELITE

Бренд: ZCS Страницы: 34

Бренд: Powerplus Страницы: 18

Бренд: Troy-Bilt Страницы: 40

Бренд: HUSTLER Страницы: 40

DECK PARK 107 M HD EL - 4WD

Бренд: Stiga Страницы: 2

Бренд: Qualcast Страницы: 15

Бренд: LAWN STAR Страницы: 7

Бренд: Yard-Man Страницы: 32

Бренд: Bad Boy Страницы: 48

PERFORMANCE 50562X89

Бренд: YARD KING Страницы: 60

Бренд: EarthWise Страницы: 8

Бренд: Toyama Страницы: 44

Бренд: Toyama Страницы: 52

Бренд: Weed Eater Страницы: 21

Бренд: Simplicity Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды