background image

 

OPERATING EQUIPMENT SAFELY 

 

 

Never allow persons to stand between power unit and mower while backing power unit up 
to hitch the mower. 

 

Before  hitching  mower  to  power  unit,  place  transmission  in  neutral,  set  park  brake,  and 
turn engine off.  Remove the ignition key. 

 

Make  sure  locking  collar  on  PTO  shaft  is  properly  locked.  If  the  PTO  shaft  comes  off 
during operation, personal injury or equipment damage could result.  

 

Always install safety chains properly when hitching mower to power unit. 

 

Tall grass can hide obstacles. Carefully walk the entire area to be mowed beforehand. Look 
for  debris,  rocks,  tree  limbs  etc.  that  will  damage  or  be  thrown  by  the  mower  blades. 
Identify objects that cannot be removed. Set mower cutting height to avoid contact. 

 

Ensure  that  no  bystanders  are  within  25  ft  of  mower  when  wing  transport  locks  are 
released. 

 

Keep all bystanders well away from the machine when it is operating. Always maintain a 
safe  operating  distance  of  300  ft  from  personnel,  other  equipment,  or 
vehicles. 

 

Never  operate  the  mower  with  deflectors  or  guards  removed.  Mower 
blades can cause small objects and debris to be thrown from under the 
mower deck at high speeds, up to 300 ft away. Objects ejected by the 
mower blades can cause severe injury. 

 

Never  tamper  with  safety  devices  or  operate  the  mower  with  them 
removed. Check proper operation regularly. 

 

Always disengage PTO, turn power unit off and remove key before dismounting, for any 
reason. 

 

Never place hands or feet under  mower deck  when the  mower is operating or power unit 
engine is running. 

 

Disengage the PTO when crossing gravel areas or roadways. 

 

Disengage the PTO and turn power unit off upon striking any  object. Inspect  mower and 
repair any damage before continuing. 

 

If the equipment should start to vibrate abnormally during operation, stop the mower, shut 
down  power  unit,  and  immediately  check  for  the  cause.  Excess  vibration  is  generally  an 
indication of a problem. Replace bent or damaged parts, do not attempt to straighten a bent 
blade. 

 

Use extreme care when operating on uneven terrain. 

 

Reduce  speed  when  operating  on  slopes  during  wet  conditions,  especially  when  making 
sharp turns.  

 

Do not use the mower in limited visibility (e.g. at dusk, in fog, heavy rain etc.). Mow only 
in daylight or good artificial light. 

 

Disengage PTO and ensure blades are completely stopped before raising wings. 

Содержание TDR-12







































































Отзывы: