Progressive Turf Equipment TDR-12 Скачать руководство пользователя | Manualshive

Страница: 15 / 70

background image

12

TIRES

:

Upon receiving your mower, check air pressure in the tires and adjust according to
specifications.

Never  inflate  tires  beyond  35  pounds  per  square  inch  (PSI)  to  seat  beads.    Inflation
beyond  35  PSI  pressure  before  seating  the  bead  may  break  the  bead  or  even  the  rim
with an explosive force.  If beads have not seated by the time the pressure has reached
35 PSI, deflate the assembly, move tire to another position on the rim and re-lubricate.
Inflate tire and inspect both sides of the tires to be sure beads are seated properly.  If
not,  deflate  tire,  unseat  beads  and  repeat  the  above  mounting  procedure.    After
properly seating beads adjust to pressure recommended.

POWER TAKE-OFF

:

Keep all safety shields in place.

When operating the power take-off, be sure the tractor shield is
always in place, covering the exposed power take-off shaft.

Before dismounting from the tractor, stop the power take-off, put
tractor in neutral, set brakes in lock position and shut off engine.

When ready to engage PTO shaft, be sure engine RPM is at idle
speed. Engaging PTO at full throttle will cause high shock loads to
driveline, with the potential for future failure.

Do not exceed the recommended PTO speed of 540 RPM

.

TIRE TYPE

RECOMMENDED TIRE

PRESSURE (PSI)

MAIN FRAME TIRES

32 PSI

«
...
13
14
15
16
17
...
»

Содержание TDR-12







































































Отзывы:

Нет отзывов

Похожие инструкции для TDR-12

Бренд: Agri-Fab Страницы: 32

Бренд: ECLOZ Страницы: 60

Бренд: P.Lindberg Страницы: 47

Бренд: Toro Страницы: 52

Бренд: MTD Страницы: 4

Бренд: Sears Страницы: 56

Бренд: Poulan Pro Страницы: 44

Бренд: Stiga Страницы: 294

Бренд: Yard force Страницы: 23

Бренд: Weed Eater Страницы: 4

Бренд: Yard-Man Страницы: 10

Бренд: Parker Страницы: 25

Бренд: Yard-Man Страницы: 4

NZMX30614KH, NZMX32734BV

Бренд: Snapper Страницы: 13

Бренд: McCulloch Страницы: 28

LMO 18-36 Battery

Бренд: Kärcher Страницы: 252

Interstater TS-100A, TS-115A,

Бренд: Alamo Страницы: 72

Бренд: Baroness Страницы: 93

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды