Progressive Turf Equipment Pro-Flex 120 Скачать руководство пользователя страница 48

Страница: 48 / 75

Pro-Flex 120 Series

Operator’s Manual

TROUBLE SHOOTING

PROBLEM

CAUSE

REMEDY

Belt slippage

Lack of tension

Inspect & replace belt or tensioner
device as required

Oily drive conditions

Clean drive

Over Loading

Increase cutting height or reduce
ground speed

Wing raising during turns

Close quarter turn valve

Rapid belt wear

Belt slippage

See Above

Belt not aligned properly

Check pulley alignment and proper
spacers

Raising

wings

with

PTO

engaged

Disengage PTO and wait for blades
to stop before raising wings

Wing raising during turns

Close quarter turn valve

Belt squeal

Belt slippage

See Above

Over-heated bearings

Belt slippage

See Above

Insufficient Lubrication

Add grease per manual

Insufficient Cooling

Clean top of deck area surrounding
spindle

Uncut strips at wings

Wing raising during turns

Close quarter turn valve

Left front deck not cutting

Wrong blade

This is a right-hand turning blade,
install RH blade

(RH blade, painted red)

Wing safety locks will not
engage

Lock chains too short

Adjust chain length

Lock springs too loose

Tighten lock springs

Mower Deck will not lower.

Orifice in cylinder plugged

Remove

orifice

and

remove

obstruction and reassemble

Deck latch in locked position.

Unlatch deck locks.

Vibration on turning

Drawbar length incorrect.

Adjust drawbar to specification

Damaged

intermediate

bearing or tractor PTO
shaft

Input shaft does not collapse
easily under power

Remove input shaft, pull apart and
deburr / grease splines

Grease at proper interval.

Premature spindle bearing
failure

Lack of lubrication or grease
contaminated

See information in manual for
grease

specification

and

compatibility.

Improper rebuild procedure

See specific instructions in manual

Improper bearings

Use only OEM bearings

Содержание Pro-Flex 120












































































Результаты поиска

Содержание Pro-Flex 120

Отзывы:

Похожие инструкции для Pro-Flex 120

Бренды по названию

Популярные бренды

Progressive Turf Equipment Pro-Flex 120, Инструкция по эксплуатации и список запасных частей

Результаты поиска

Содержание Pro-Flex 120

Отзывы:

Похожие инструкции для Pro-Flex 120

Бренды по названию

Популярные бренды