Progressive Turf Equipment Pro-Flex 120 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 75

background image

Pro-Flex 120 Series

Operator’s Manual

43

SUPPORTING MACHINE FOR SERVICE

(2) Points are available to lift the mower off of the ground for servicing
the transport tires / wheels / bearings at the base of the axle as shown
in the accompanying illustration. Use a bottle or service jack to raise
the wheel from the ground and place a wooden block or other suitable
support under the rectangular tube.

Do not support the machine on cinder blocks, hollow tiles or
other members that may fail under continuous load.

Never perform service on a machine that is supported solely by a
jack. Always ensure proper blocking is placed to support load
during service.

Transport  tires  must  be  changed  with  the  wings  in  the  raised
position.    Ensure  the  machine  is  on  a  flat,  level surface  and  the
wing  locks  are  fully  engaged  before  attempting  to  lift  the
machine.

TRANSPORT TIRES

Inspect tires daily for wear or damage. Check tire pressures weekly

with an accurate pressure gauge. Do not inflate tires beyond 35 psi.

Mounting and dismounting tires from rims can be dangerous and
should be performed by trained personnel using correct tools,
equipment and procedures.

LONG-TERM STORAGE

If the mower is not to be used for an extended period of time (4
months or longer) it is recommended that the following maintenance
steps are followed:

1) Thoroughly wash mower, removing all grass clipping residue

from deck undersides & mower framework.

2) Add grease to all grease points.

3) Check gearbox oil for proper level.

4) Relieve tension on all V-belts by removing belt from tensioner

pulley.

5) Inspect all drive belts & pulleys.

6) Inspect all blade spindle bearings for excessive play.

7) Inspect all blades for serviceable condition.

When returning the mower to service after long-term storage:

1) Check tightness of all blade fasteners.

2) Add grease to all grease points.

3) Re-install all V-belts on tensioner pulleys.

4) Ensure all pivot points move freely.

5) Change gearbox oil.

«
...
45
46
47
48
49
...
»

Содержание Pro-Flex 120












































































Отзывы:

Нет отзывов

Похожие инструкции для Pro-Flex 120

Бренд: Agri-Fab Страницы: 32

Бренд: P1PE Страницы: 28

Бренд: Yard-Man Страницы: 24

Бренд: MTD Страницы: 16

Бренд: Ransomes Страницы: 184

Бренд: Weed Eater Страницы: 48

Бренд: Poulan Pro Страницы: 4

Бренд: Alamo Industrial Страницы: 186

Бренд: Feider Machines Страницы: 22

Бренд: Gardeo Страницы: 60

Бренд: Ferris Страницы: 60

Бренд: Ranger Страницы: 38

Бренд: Scag Power Equipment Страницы: 96

Бренд: Snapper Страницы: 72

Бренд: Craftsman Страницы: 36

Бренд: Kubota Страницы: 117

Бренд: Ferrari Страницы: 56

Бренд: FLORABEST Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды