Progressive Turf Equipment Pro-Flex 120 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 75

background image

Pro-Flex 120 Series

Operator’s Manual

41

SPINDLE ASSEMBLY REPAIR

Note: A video showing this rebuild procedure is available on our
website:

http://www.progressiveturfequip.com/service

Spindle  repair  requires  special  skills  and  tools,  a  shop  press  is
required.    If  your  shop  is  not  properly  equipped  or  your
mechanics  are  not  properly  trained  in  this  type  of  repair,
complete spindle assemblies are available as service parts.

1) Remove LH Nut (3), lock washer (2), pulley (1), spacer (12),

washer (8) & shim (4) from spindle assembly.

The spindle nut

is left-hand thread.

Make  sure  that  the  press  ram  and  bed  100%  square  to  each
other.    If  bearings  are  not  square  in  housing,  bearings  will wear
out prematurely.

2) Place assembly in shop press with support under spindle

housing flange and press spindle down through housing.

3) Remove bottom bearing from spindle and top bearing from

housing

IMPORTANT! Removing bearings from spindle / housing
causes permanent damage to the bearings. New bearing

must

be used in re-assembling the spindle

.

4) Inspect bearing spacer faces for wear. If any wear is present,

replace spacer with new.

IMPORTANT! Failure to replace a worn or damaged spacer
will lead to premature top bearing wear.

5) Place housing in press (upside down).

Pressing on outer

race

; install bottom bearing (11) into housing.

6) Place spindle in press. Place dirt shield (8) and shim (7) on

spindle.

7)

Pressing on

inner race

of bottom bearing, press housing /

bearing on to spindle. A steel tube will be required to slide over
the spindle and press on inner race.

8) Install bearing spacer (6) with hole end up.

9) Set top bearing on to spindle.

Pressing on inner race

, press

top bearing on to spindle.

IMPORTANT! Due to design tolerances, the top bearing
may appear to be loose in the housing. This is normal and
is

not

detrimental to the operation of the spindle.

10) Install shim washer (4), dirt shield (8), pulley spacer (12), key

(15), pulley (1) and set screw (14) on to spindle.

11) Install LH lock washer (2) and LH nut (3) and torque to 60 ft-lb.

Rotate the housing six revolutions by hand and check for smooth, free
movement.

The assembly is now ready for installation into the mower deck.

«
...
43
44
45
46
47
...
»

Содержание Pro-Flex 120












































































Отзывы:

Нет отзывов

Похожие инструкции для Pro-Flex 120

Бренд: Ariens Страницы: 32

Бренд: Gardol Страницы: 324

Бренд: Yard-Man Страницы: 8

pro-turn 460 diesel 992236

Бренд: Gravely Страницы: 51

Бренд: Feider Machines Страницы: 22

Бренд: Mountfield Страницы: 50

Бренд: Honda Страницы: 107

Бренд: Murray Страницы: 168

Бренд: Spearhead Страницы: 32

Бренд: California Trimmer Страницы: 8

Бренд: Toro Страницы: 44

Бренд: VITO GARDEN Страницы: 24

Bob-Cat 942237F

Бренд: Schiller Grounds Care Страницы: 40

REELMASTER 6500 D

Бренд: Toro Страницы: 258

Бренд: Giant-Vac Страницы: 36

Бренд: EINHELL Страницы: 84

Бренд: EINHELL Страницы: 112

Бренд: EINHELL Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды