Progressive Turf Equipment Pro-Flex 120 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 75

background image

Pro-Flex 120 Series

Operator’s Manual

37

“V” BELT DRIVE

BELT TENSION - 100h / Monthly

Proper  belt  tension  is  a  fundamental  factor  in  successful  V-belt
operation.  Lack of tension will cause slippage, and too much tension
will  cause  excessive  belt  stretch  as  well  as  damage  to  the  drive
components, such as bearings and shafts.  To assess the condition of
the automatic tensioner, the following procedure is recommended.

At  the  mid-point  of  the  span,  apply  a  deflection  force  with  a  spring
scale  in  the  direction  perpendicular  to  the  span  until  the  belt  is
deflected the 3/8”.
The recommended force to deflect the belt is a minimum of 5 lbs. to a
maximum of 7 lbs.
The  first  24  to  48  hours  of  operation  is  the  belt  “run  in”  period.    To
ensure satisfactory belt performance, belt tension should be checked
during this time period.

BELT ADJUSTMENT

All deck drive belts utilize an automatic rubber torsion tensioning
device. These tensioners are pre-set upon installation and require no
further adjustment or maintenance.

In normal service the tensioner arm angle (see detail at right) should
read between 30 degrees (new belt) and 15 degrees.

A tool is provided to allow easy release of belt tension using a ½”
drive breaker bar or ratchet.

«
...
39
40
41
42
43
...
»

Содержание Pro-Flex 120












































































Отзывы:

Нет отзывов

Похожие инструкции для Pro-Flex 120

Бренд: Land Pride Страницы: 60

Бренд: Makita Страницы: 52

Бренд: Toro Страницы: 2

Бренд: Jacobsen Страницы: 50

Бренд: Grizzly Страницы: 96

Бренд: Toro Страницы: 24

GRA Professional 36V-48

Бренд: Bosch Страницы: 128

Бренд: Bosch Страницы: 67

Бренд: Bosch Страницы: 398

Бренд: Bosch Страницы: 318

Бренд: Bosch Страницы: 448

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 64

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды