background image

REHATEAM s.r.l.—vicolo Negrelli 

5

31040 

Castagnole di Paese TV  

-

 www.rehateamprogeo.com

 

Service Manual JOKER JUNIOR 2.0    10

 

 

 

SERVICE MANUAL 

SETTING (point of balance) 

 

1    2     3     4 

12.5   12.5  12.5  

REF. 

25        25  

X  

1    2     3     4 

Y  

1      3     

PRUDENTIAL

, S = 60 mm approx. 

Plate fixed through holes 

1

 and 

3

 leaving in 

sight two frame holes between the plate and 

the nut 

E

 that fix the backrest support. 

2  4 

STANDARD

, S = 72.5 mm approx. 

Plate fixed through holes 

2

 and 

4

 leaving in 

sight two frame holes between the plate and 

the nut 

E

 that fix the backrest support. 

1  3 

ACTIVE

, S = 85 mm approx. 

Plate fixed through holes 

1

 and 

3

 leaving in 

sight  three  frame  holes  between  the  plate 

and the nut 

E

 that fix the backrest support. 

You can adjust the setting 

S

 by moving the posts 

A

 (to which the rear axle is fixed) along the 

frame. The frame has pre-drilled holes every 25 mm.  

The post fixing plate 

B

 has 4 holes, 12.5 mm from one another. Such holes allows for inter-

mediate adjustment. 

To change setting, remove both nuts/washers 

D

 that fix the bolt 

C

. screw off the bolts i 

C

 (the 

holes of the plate 

B

 are threaded). 

Repeat the same operation on both sides of the wheelchair. 

WARNING

: if you remove only one nut and then try to unscrew the corresponding bolt, this 

bolt may result particularly hard to unscrew because the second one, still tightened with the 
nut, can create a pressure on the first.  

If you wish to make the setting 12.5 mm 

MORE ACTIVE

, starting from the position as shown 

in the picture RIF. (bolts 

C

 fixed through holes 

2

 and 

4

), move the post 

A

 forward along the 

frame until aligning the hole 

with the closest hole of the frame, in this case 

X

The hole 

3

 will consquently be aligned. 

If you move the post forward by another 12.5 mm, the hole 

2

 will align to the frame hole 

X

The hole 

4

 will consquently be aligned. 

If you wish to make the setting 12.5 mm 

MORE PRUDENTIAL

, starting again from the posi-

tion as shown in the picture RIF. (bolts 

C

 fixed through holes 

2

 and 

4

), move the post 

A

 back-

ward along the frame until aligning the hole 

to the frame hole where the hole 

4

 was aligned. 

The hole 

4

 will consequently be aligned. 

If you move the post backward by another 12.5 mm, the hole 

4

 will align to the frame hole 

Y.

 

The hole 

2

 will consequently be aligned. 

Once  you  have  determined  the  new  setting,  screw  the  bolts 

C

  on  the  plate 

B

  all  the  way 

down. Then, insert washers and nuts 

D

 and fix them while holding the corresponding bolts. 

While you tighten the nut 

D

, hold the bolt 

C

 otherwise the bolt will loosen. 

Following the instructions above, you can obtain other more active or prudential settings

.

 

The pictures 1, 2 and 3 show the combinations to get the three pre-determined settings. 

Check and adjust the for angle. 
Adjust the brakes. 
Modify the mudguards. 

Содержание JOKER JUNIOR 2.0



























Отзывы: