Procom MNSD300HGA Скачать руководство пользователя страница 13

Страница: 13 / 32

www.usaprocom.com

200233-01B

INSTALLATION

6. Replace heater onto mounting bracket.
7. Place spacers between bottom mounting

holes and wall anchor or drilled hole.

8. Hold spacer in place with one hand. With

other hand, insert mounting screw though

bottom mounting hole and spacer. Place

tip of screw in opening of wall anchor or

drilled hole.

CONNECTING TO GAS SUPPLY

WARNING: A qualified ser-

vice technician must connect

heater to gas supply. Follow all

local codes.

WARNING: This appliance

requires a 3/8" NPT (National

Pipe Thread) inlet connection to

the pressure regulator.

WARNING: For natural gas,

Never connect heater to private

(non-utility) gas wells. This gas is

commonly known as wellhead gas.

WARNING: Do not over-

tighten gas connections.

CAUTION: Use only new, black

iron or steel pipe. Internally tinned

copper tubing may be used in

certain areas. Check your local

codes. Use pipe of 1/2" diameter

or greater to allow proper gas vol-

ume to heater. If pipe is too small,

undue loss of pressure will occur.

CAUTION: For natural gas,

check your gas line pressure

before connecting heater to gas

line. Gas line pressure must be

no greater than 9.5" of water. If

gas line pressure is higher, heater

regulator damage could occur.

CAUTION: For propane/

LP gas, Never connect heater

directly to the gas supply. This

heater requires an external regu-

lator (not supplied). Install the

external regulator between the

heater and gas supply.

CAUTION: Avoid damage to

regulator. Hold gas regulator

with wrench when connecting

into gas piping and/or fittings.

CAUTION: Use pipe joint

sealant that is resistant to gas

(Propane/LP or Natural Gas).

Before installing heater, make sure you have

the items listed below:
• piping (check local codes)
• sealant (resistant to natural gas and pro-

pane/LP gas)

•  equipment shutoff valve*
•  test gauge connection*
•  sediment trap
•  tee joint
•  pipe wrench
•  flexible gas hose (check local codes)
•  3/8" NPT brass fitting
* A  CSA  design-certified  equipment  shutoff

valve with 1/8" NPT tap is an acceptable al-

ternative to test gauge connection. Purchase

the optional CSA design certified equipment

shutoff valve from your dealer.

9. Tighten both screws until heater is firmly

secured to wall. Do not over tighten.

Note: Do not replace front panel at this time.

Replace front panel after making gas connec-

tions and checking for leaks.

Содержание MNSD300HGA

































Результаты поиска

Содержание MNSD300HGA

Отзывы:

Похожие инструкции для MNSD300HGA

Бренды по названию

Популярные бренды

Procom MNSD300HGA, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание MNSD300HGA

Отзывы:

Похожие инструкции для MNSD300HGA

Бренды по названию

Популярные бренды