background image

www.usaprocom.com

200233-01B

16

OPERATION

FOR YOUR SAFETY READ BEFORE LIGHTING

 WARNING: If you do not fol-

low these instructions exactly, a 

fire or  explosion may result caus-

ing property damage, personal 

injury or loss of life.

A.  This appliance has a pilot which must 

be lighted by hand. When lighting the 

pilot, follow these instructions exactly.

B.  BEFORE LIGHTING smell all around 

the appliance area for gas. Be sure to 

smell next to the floor because some 

gas is heavier than air and will settle 

on the floor.

 

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do 

not use any phone in your building.

• Immediately call your gas supplier 

from a neighbor’s phone. Follow the 

gas supplier’s instructions.

• If you cannot reach your gas supplier, 

call the fire department.

C.  Use only your hand to push in or turn 

the gas control knob. Never use tools. 

If  the  knob  will  not  push  in  or  turn 

by  hand,  don’t  try  to  repair  it,  call  a 

qualified service technician. Force or 

attempted repair may result in a fire or 

explosion.

D.  Do not use this appliance if any part 

has been under water. Immediately call 

a qualified service technician to inspect 

the appliance and to replace any part of 

the control system and any gas control 

which has been under water.

1.  STOP! Read the safety information above.
2.  Make sure equipment shutoff valve is fully 

open.

3.  Turn control knob clockwise 

 to the 

OFF position.

4.  Wait five (5) minutes to clear out any air. 

Then  smell  for  gas,  including  near  the 

floor. If you smell gas, STOP! Follow "B" 

in the safety information above. If you do 

not smell gas, go to the next step.

5.  Turn control knob counterclockwise 

 

to  the  PILOT  position.  Press  in  control 

knob for five (5) seconds (see Figure 19).

 

Note: The first time that the heater is oper-

ated after connecting the gas supply,the 

control knob should be pressed for about 

thirty (30) seconds. This will allow air to 

bleed from the gas system. If pilot does 

not stay lit, refer to Troubleshooting, pages 

20  though  24. Also  contact  a  qualified 

service technician or gas supplier for 

repairs. Until repairs are made, light pilot 

with match.

• If  control  knob  does  not  pop  up  when 

released,  contact  a  qualified  service 

technician or gas supplier for repairs.

6.  With  control  knob  pressed  in,  push 

down  and  release  ignitor  button.  This 

will  light  pilot.  The  pilot  is  attached  to 

the  front  of  burner.  The  pilot  can  be 

seen  through  the  grill.  If  needed,  keep 

pressing  ignitor  button  until  pilot  lights.

 

Note: If pilot does not stay lit, refer to 

Troubleshooting, pages 20 though 24. 

Also contact a qualified service technician 

or gas supplier for repairs. Until repairs 

are made, light pilot with match. To light 

pilot with match, see Manual Lighting 

Procedure

, page 18

.

7.  Keep control knob pressed in for 30 sec-

onds after lighting pilot. After 30 seconds, 

release control knob. If control knob does 

not pop up when released, contact a quali-

fied service technician or gas supplier for 

repairs.

MODEL MNSD300HGA

LIGHTING INSTRUCTIONS

OFF

Pilot/IGN

LOW

MED

HIGH

Figure 19 - Control Knob in the OFF 

Position

Ignitor Button

Control Knob

Содержание MNSD300HGA

































Отзывы: