background image

www.usaprocom.com

200233-01B

4

1.  Do not place Propane/LP supply tank(s) 

inside any structure. Propane/LP supply 

tank(s) must be placed outdoors.

2.  Heaters  with  a  maximum  input  over 

6,000  Btu/Hr  shall  not  be  installed  in  a 

bathroom. Heaters with a maximum input 

over 10,000 Btu/Hr shall not be installed 

in a bedroom.

3.  This heater needs fresh air ventilation to 

run properly. This heater has an Oxygen 

Depletion Sensing (ODS) safety shutoff 

system. The ODS shuts down the heater 

if not enough fresh air is available. See 

Air for Combustion and Ventilation

, pages 

6 and 7. If heater keeps shutting off, see 

Troubleshooting

, page 20.

4.  Keep all air openings in front and bottom 

of heater clear and free of debris. This will 

ensure enough air for proper combustion.

5.  If heater shuts off, do not relight until you 

have provided fresh, outside air. If heater 

keeps shutting off, have it serviced.

6.  Do not run heater:

• Where flammable liquids or vapors are 

used or stored.

• Under dusty conditions.

SAFETY

7.  Before using furniture polish, wax, carpet 

cleaner, or similar products, turn heater 

off. If heated, the vapors from these prod-

ucts may create a white powder residue 

within burner box or on adjacent walls or 

furniture.

8.  Always  run  heater  with  control  knob  at 

PILOT/IGN, LOW (1) or HIGH (5) locked 

positions. Never set control knob between 

locked  positions.  Poor  combustion  and 

higher  levels  of  carbon  monoxide  may 

result.

9.  Do not use heater if any part has been 

under water. Immediately call a qualified 

service technician to inspect the room 

heater  and  to  replace  any  part  of  the 

control system and any gas control which 

has been under water.

10. Turn off and unplug heater and let cool 

before servicing. Only a qualified service 

person should service and repair heater.

11. Operating  heater  above  elevations  of 

4,500 feet could cause pilot outage.

12. To  prevent  performance  problems,  do 

not use propane/LP fuel tank of less than 

100 lbs. capacity.

SPECIFICATIONS

MODEL 

MNSD300HGA

MNSD300TGA

Ignition

Piezo Ignitor

Piezo Ignitor

Gas Type

Using Natural Gas 

Using Natural Gas

BTU (available)

Min. 15,000 Max. 30,000 Min. 15,000 Max. 30,000

Pressure Regulator Setting

4" W.C.

4" W.C.

Inlet Gas Pressure*
(inches of water)

Maximum 9.5"

Maximum 9.5"

Minimum 5"

Minimum 5"

Gas Type

Using Propane Gas

Using Propane Gas

BTU (available)

Min. 15,000 Max. 30,000 Min. 15,000 Max. 30,000

Pressure Regulator Setting

9" W.C.

9" W.C.

Inlet Gas Pressure*
(inches of water)

Maximum 14"

Maximum 14"

Minimum 11"

Minimum 11"

Heater Dimensions (HxWxD)

23 

1

/

2

" × 26 

5

/

8

" × 8"

23 

1

/

2

" × 26 

5

/

8

" × 8"

Carton Dimensions (HxWxD)

25 

3

/

4

" × 28 

1

/

2

" × 9 

1

/

4

"

25 

3

/

4

" × 28 

1

/

2

" × 9 

1

/

4

"

Heater Weight

27.6 lbs

29.6 lbs

Shipping Weight

32.6 lbs

34.6 lbs

Содержание MNSD300HGA

































Отзывы: