PROBOIL PROBOIL.4E Скачать руководство пользователя | Manualshive

Страница: 29 / 44

background image

PROBOIL.4E user & installation guide v1d

29

2

2

2

2

PROBOIL.

PROBOIL.

PROBOIL.

PROBOIL.4E

4E

4E

4E installer guide

installer guide

installer guide

installer guide

2.1

2.1

2.1

2.1 Important technical data:

Important technical data:

Important technical data:

Important technical data:

Boiler:

Boiler:

Boiler:

Boiler:

Measure:

Comments:

Model

PROBOIL.4E

Boiler type

Vented (unpressurised) displacement system

Unit dimensions

206x256x291mm (without connectors attached)

Overall weight

9 kg (Apx. when full)

Ambient operating temperature

+5°C to +40°C (indoor use heated space only)

Minimum cold input pressure

2 bar (recommended), assuming a minimum acceptable flow rate of 1 litre
per minute.

Maximum cold input pressure

5.5 bar, if incoming cold water pressure is above this value than a pressure
reducing valve must be installed.

Boiling tank capacity

4 /- 5%

Typical usable volume

Dependent on temperature selection, when set to 98°C approximately 3.0
litres above 90° and approximately 1.5 litres before incoming cold water
decrease the output temperature when dispensed continuously.

Maximum Chlorine value for
incoming water

100mg/l

Tank material

Stainless steel (304)

Selectable in tank temperatures

98° Maximum with adjustable heating point adjustment on screen
(75, 85, 90, 95, 96, 97- 98°C range)

Heat up time

From 20°C to 98°C
1 litre usage recovery, approximate time 18 minutes
2 litre usage recovery, approximate time 12 minutes
3 litre usage recovery, approximate time 8 minutes
4 litre usage recovery, approximate time 9 minutes
Up to apx. 100 UK cups per hour dependant on environmental and usage
conditions

Thermal loss

Apx. 3-4°C. loss from tank to spout exit
Varies according to tap model, environmental and usage conditions

Safety devices

-

vented (unpressurised) tank

-

minimum water level float switch to prevent dry heating

-

digital thermal monitoring and control

-

digital self-diagnostic control

-

one shot dry burn 120°C thermal fuse (non-resettable)

-

blow off connection for accidental blockage protection

Supply voltage range

AC 220-240V (50Hz)

Max. Power usage

(element on)

2.15kW at 240V AC

Power usage

Standby (screen off)

0.5W

Power usage

(keep warm at 98°C)

0.043kWh, depending on ambient temperature, power on, no water usage.

Power usage

(reboil 1 litre at 98°C)

0.1kWh (based on single 1 litre dispense of 98°C)

Power lead

1.4M (cable), 3 pin UK plug (13A), IEC connector, do not extend or replace.

Filter

Filter

Filter

Filter cartridge

cartridge

cartridge

cartridge:

:

:

:

«
...
27
28
29
30
31
...
»

Содержание PROBOIL.4E













































Отзывы:

Нет отзывов

Похожие инструкции для PROBOIL.4E

Бренд: IBC Страницы: 4

Бренд: IBC Страницы: 6

Бренд: IBC Страницы: 74

Бренд: Quantec Страницы: 44

Planet AquaQuick 25 BF

Бренд: Sime Страницы: 116

CIAO GREEN R.S.I

Бренд: Beretta Страницы: 51

ecoTEC VC 406/5

Бренд: Vaillant Страницы: 72

Бренд: Orlanski Страницы: 56

Luna Duo-Tec MP Plus 1.35

Бренд: Baxi Страницы: 34

Бренд: Camus Hydronics Страницы: 90

Бренд: Biodom Страницы: 50

Бренд: Crown Boiler Страницы: 42

Бренд: Taco Страницы: 6

Бренд: Saunier Duval Страницы: 4

VITORONDENS 200-T

Бренд: Viessmann Страницы: 32

Vitorond 200 Series

Бренд: Viessmann Страницы: 28

Бренд: Viessmann Страницы: 32

VITORADIAL 300-T

Бренд: Viessmann Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды