PROBOIL PROBOIL.4E Скачать руководство пользователя | Manualshive

Страница: 34 / 44

background image

PROBOIL.4E user & installation guide v1d

34

2.3.2 Install the tap

⚠

YOU MUST INSTALL THE TAP FIRST BEFORE COMMENCING THE BOILER INSTALLATION



Installation of the tap will vary from model to model, you must now refer to the separate installation guide

supplied with the tap or dispenser at this time.

1)

Install the tap as per the model specific guidelines supplied with each tap connect the domestic cold (and hot if
applicable) water inputs to the tap.

2)

Check you have the right hoses attached to the right inlets and outlets of the tap, you can quickly do this by very
slowly part opening the operating handle(s) to an on position and checking for output being out of the expected
hose into a bucket or similar.

⚠

With all handles in the off position, blow through the tap boiled water hose (X5). If connected correctly air

should pass freely to the centre spout channel.

«
...
32
33
34
35
36
...
»

Содержание PROBOIL.4E













































Отзывы:

Нет отзывов

Похожие инструкции для PROBOIL.4E

Alpha CB50 Boiler

Бренд: Alpha Страницы: 36

QUADRIFOGLIO B 125

Бренд: Ferroli Страницы: 124

Бренд: Worcester Страницы: 52

Бренд: Saunier Duval Страницы: 15

Бренд: Cygnet Страницы: 2

Бренд: Buderus Страницы: 64

Logano plus GB402

Бренд: Buderus Страницы: 76

Бренд: elco Страницы: 96

Бренд: Potterton Страницы: 56

Vitoflame 300 VHG III

Бренд: Viessmann Страницы: 36

Бренд: Unical Страницы: 48

Бренд: U.S. Range Страницы: 8

Бренд: U.S. Boiler Company Страницы: 7

Бренд: TriangleTube Страницы: 24

Бренд: Burnham Страницы: 68

Бренд: Burnham Страницы: 72

DOMIproject F 24

Бренд: Ferroli Страницы: 56

Бренд: Laars Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды