INTRODUCTION
© 2018 Global Welding LLC
Page
15
Operating Manual No: PWOM-215/250MP-001
3.5
250MP Duty Cycle at 208/230/240 VAC
The rated duty cycle of the Power Source, is a statement of the time
it may be safely operated at its rated Welding Amperage output.
MIG (GMAW/FCAW) @ 208/230/240 VAC
(25% Duty Cycle at 250 A)
2.5 Minutes Welding
in any 10 Minute Period
7.5 Minutes Non-Welding
in any 10 Minute Period
STICK (SMAW) @ 208/230/240 VAC
(25% Duty Cycle at 250 A)
2.5 Minutes Welding
in any 10 Minute Period
7.5 Minutes Non-Welding
in any 10 Minute Period
LIFT TIG (GTAW) @ 208/230/240 VAC
(25% Duty Cycle at 250 A)
2.5 Minutes Welding
in any 10 Minute Period
7.5 Minutes Non-Welding
in any 10 Minute Period
3.6
P
RO
-
TEC
215MP Multi-Process Package
P
RO
-
TEC
215MP Multi-Process Package,
Part No. G1621500
, comes complete with:
Power Source with 250 V NEMA 6-50P Plug, 10 ft 12AWG Cable
Power Adapter 250 V/50 A to 120 V/15 A
1/8 in., E6013 Sample Electrodes, Qty 4
MIG Gun 10 ft 215 A
Electrode Holder & Cable 10 ft
Argon Flow-gauge Regulator
Operating Manual
17 TIG Torch 12.5 ft
TIG Accessory Kit
Ground Clamp & Cable 10 ft
Gas Hose (12.5 ft)
3.7
P
RO
-
TEC
250MP Multi-Process Package
P
RO
-
TEC
250MP Multi-Process Package,
Part No. G1625000
, comes complete with:
Power Source with 250 V NEMA 6-50P Plug, 10 ft 12AWG Cable
Power Adapter 250 V/50 A to 120 V/15 A
1/8 in., E6013 Sample Electrodes, Qty 4
MIG Gun 12 ft 250 A
Electrode Holder & Cable 10 ft
Argon Flow-gauge Regulator
Operating Manual
17 TIG Torch 12.5 ft
TIG Accessory Kit
Ground Clamp & Cable 10 ft
Gas Hose (12.5 ft)
3.8
Definitions of Terms Used
MIG SYN
: Pre loaded MIG (GMAW/FCAW) welding param-
eters for easy setup of Fe, Ss, Al, FCAW-S,
FCAW-G Welding Wire using a MIG Gun only.
MIG MAN:
MIG (GMAW/FCAW) welding parameters are
setup by the Operator for most Welding Wire
with a MIG Gun or Spool Gun.
Memory Button
: Save or Recall your weld programs
from a memory chip inside the Power Source.
TIG:
Pre loaded DC Lift TIG (GTAW) welding parame-
ters for easy setup based on the selected tung-
sten electrode size.
STICK:
Pre loaded DC STICK (SMAW) welding parame-
ters for easy setup the selected STICK electrode
type and size.
Fe
:
Mild steel MIG welding.
Ss
:
Stainless steel MIG welding.
Al
:
Aluminum MIG welding.
FCAW-S:
Flux Cored Arc Welding (self shielded).
FCAW-G:
Flux Cored Arc Welding (gas shielded).
Arc Force (DIG):
Additional amperage during low voltage
(short arc length) conditions while welding.
Downslope:
The gradual ramping down of weld amperage
over a period of time.
Inductance:
For
MIG SYN
or
MIG MAN
modes only. Adjusts
the intensity of the MIG welding arc.
Post Flow Gas:
For
LIFT TIG
mode only. The time Gas flows
after the arc has extinguished to cool the Tung-
sten Electrode and reduce oxidization.
50 Dinse Style:
Welding terminal connector.
120 VAC / 15 A Outlet (Nema 5-15R):
North American
homes / workshops are wired with 15 Amp,
120-volt circuits with 14-gauge wire and is pro-
tected by a 15 Amp circuit breaker or fuse.
Nema 5-15P:
3 prong power cord plug and rated to 120 V
/ 15 A.
120 VAC / 20 A Outlet (Nema 5-20R):
North American
homes / workshops are wired with 20 Amp,
120-volt circuits with 12 or 10-gauge wire and
is protected by a 20 Amp circuit breaker or fuse.
Nema 6-50P:
Heavy duty 3 prong power cord plug and
rated to 250 V / 50 A.
Nema 6-50R:
Heavy duty 3 prong socket and rated to 250
V / 50 A.
AWG:
American Wire Gauge (AWG) is a standard set
of non-ferrous electrical wire conductor sizes.
Duty Cycle:
The welding time period (arc on time) as a per-
centage over a 10 minute period.
KVA:
Kilovolt-ampere is 1000 volt-amperes where
volt-ampere is the multiplication of volt x am-
pere.
OCV:
Nominal Open Circuit Voltage at the welding
terminals.
Delay Fuse:
Time Delay Fuse to UL class RK5.
NOTE 1:
P
RO
-
TEC
reserves the right to change, improve or revise the
specifications or design of these products without prior notice. Such
updates or changes do not entitle the buyer of equipment previously
sold or shipped to the corresponding changes, updates, improvements
or replacement. The values specified in the table above are nominal
parameters, your products parameters may differ. Individual Power
Source may differ from the above specifications due to in part, but not
exclusively, to any one or more of the following; variations or changes
in manufactured components, installation location / conditions and
local Input Power Supply Grid conditions.
(Spool Gun)
