Pro Mach ORION Sentry HP Скачать руководство пользователя страница 83

Страница: 83 / 100

Orion

Machine Manual

Revision 3.1

Sentry HP/ LP Flex Stretchwrapper

21 May 2020

System Operation

Page 3-51

FAULTS EXIST

Faults currently exist.

Correct the cause of the fault.
Press reset to reset the fault con-
dition once the cause is cor-
rected.

CARRIAGE MOVING

UP TOO SLOWLY

The carriage is moving upward too slowly.

Check for the cause of the car-
riage not moving correctly.
Check the belt drive behind the
back panel. Check for a jam or
obstruction on the track.

CARRIAGE MOVING

DOWN TOO SLOWLY

The carriage is moving downward too slowly.

Check for the cause of the car-
riage not moving correctly.
Check the belt drive behind the
back panel. Check for a jam or
obstruction on the track.

MULTISTRETCH VFD

NOT READY

The indicated VFD is not ready to run.

Check the fault code on the VFD
display in the electrical cabinet.
See VFD manual for fault code
information.

MAIN DRIVE VFD NOT

READY

CARRIAGE VFD NOT

READY

DOWNLOADING VFD

PARAMETERS -

PLEASE WAIT

The VFD parameters are transferring to the
VFD’s from the PLC.

Wait until the process is com-
pleted.

X2X

COMMUNICATION

FAULT - PRESS E-STOP

TO CLEAR FAULT

There is an X2X communication fault, press and
release the E-stop button to clear the fault.

Contact Orion Packaging if
problem persists.

RS485

COMMUNICATION

FAULT - PRESS E-STOP

TO CLEAR FAULT

There is an RS485 communication fault, press
and release the E-stop button to clear the fault.

Contact Orion Packaging if
problem persists.

Table 3-36. The Information and Alarm Displays (Continued)

MESSAGE

DESCRIPTION

CORRECTION

Содержание ORION Sentry HP





































































































Результаты поиска

Содержание ORION Sentry HP

Отзывы:

Похожие инструкции для ORION Sentry HP

Бренды по названию

Популярные бренды

Pro Mach ORION Sentry HP, Руководство пользователя

Результаты поиска

Содержание ORION Sentry HP

Отзывы:

Похожие инструкции для ORION Sentry HP

Бренды по названию

Популярные бренды