Prism Hardscapes Moderno 5 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 23

Prism Hardscapes Moderno 5 Скачать руководство пользователя страница 6

2.3 GAS & ELECTRONIC REQUIREMENTS

INPUT VOLTAGE: 120 VAC/60 HZ to transformer

OUTPUT VOLTAGE (transformer to appliance): 12 VAV/60 HZ

GAS TYPE: Natural Gas Propane Gas

GAS PRESS 7 inches Water Column 11 inches Water Column

GAS INPUT FLOW 85,000 BTU/HR 85,000 BTU/HR

RECOMMENDED CLEARANCES TO COMBUSTIBLE SURFACES: SIDES: 4 FT TOP: 6 FT

Note:

Check with your gas supplier to verify gas flows and pressures available at the location of your

installation. In many cases utility companies will install larger meters at no charge to accommodate
larger flows.

WARNING

THIS PRODUCT OPERATES WITH 12 AC INPUT

DO NOT ATTEMPT TO CONNECT 120 VACS DIRECTLY TO THE APPLIANCE FOR IT

MAY CAUSE PERMANENT DAMAGE

2.4 PRODUCT CONTENTS

PART NAME

QTY

BURNER & BURNER PLATE

1

PILOT ASSEMBLY (PILOT BURNER, IGNITOR, SENSOR $ HOOD)

1

IGNITION CONTROL BOX

1

HEAT SHIELD

1

HEAT SHIELD JAM NUT

1

ORIFICE SET (BURNER & PILOT)

1

TRANSFORMER (120VAC/12VAC)

1

«
...
4
5
6
7
8
...
»

Содержание Hardscapes Moderno 5
























Отзывы:

Нет отзывов