Princeton Instruments NIRvana-LN Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 122

Princeton Instruments NIRvana-LN Скачать руководство пользователя страница 52

52

NIRvana

™

-LN System Manual

Issue 4

4.

Connect the shutter cable between the entrance slit shutter and the NIRvana-LN

Shutter

connector.

•

External Slit Shutter
A shutter assembly mounted externally to the spectrograph has shutter cable that
plugs into the

Shutter

connector.

•

Internal Slit Shutter
A shutter mounted internally has an external shutter connector in the sidewall of the
spectrograph. Connect a shutter cable from the NIRvana-LN

Shutter

connector to

that connector.

5.

Turn on power to the detector and fill the Dewar.

NOTE:

The detector must be turned on before WinSpec/32 is
launched.

6.

Turn on power to the spectrograph.

7.

Turn on power to the host computer.

8.

Launch WinSpec/32.

6.4 Configure NIRvana-LN Parameters

Perform the following procedure to configure WinSpec/32 with appropriate NIRvana-LN
configuration parameters:

1.

From the WinSpec/32 menu bar, select

Setup —> Environment

to display the

Environment

dialog.

Review the DMA Buffer size information and make any changes that are necessary.
Large arrays (e.g., 2048 x 2048,) require a buffer size on the order of 32 MB. If the
buffer size needs to be changed, the host computer must be rebooted in order for the
new memory allocation to take effect.

NOTE:

After rebooting the host computer, WinSpec/32 must be
launched again.

2.

From the WinSpec/32 menu bar, select

Setup —> Hardware

to display the

Hardware

Setup

dialog. Select the

Controller/Camera

tab.

Verify and/or configure the parameters as indicated in

.

Table 6-1: WinSpec/32 Hardware Configuration

Parameter

Value

Notes

Controller Type

—

This information is read from the camera.

Camera Type

—

This information is read from the camera.

Shutter Type

Custom

System dependent.

Readout Mode

Full Frame

Available modes are read from the camera.

«
...
50
51
52
53
54
...
»

Содержание NIRvana-LN



























































































































Отзывы:

Нет отзывов