Princeton Instruments NIRvana-LN Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 122

Princeton Instruments NIRvana-LN Скачать руководство пользователя страница 30

30

NIRvana

™

-LN System Manual

Issue 4

4.4.2

WinView/32 and WinSpec/32 Host Computer Requirements

When running WinView/32 or WinSpec/32 data acquisition software, the host computer
must meet, or exceed, the following specifications:

•

32-Bit

Operating System

—

Windows 7.

•

2 GHz Pentium

®

4 (minimum);

•

2 GB RAM (minimum);

•

CD-ROM drive;

•

At least one unused PCI card slot (32-bit) (PCI 2.3 compliant, 33/66 MHz bus)

•

Super VGA monitor and graphics card
Supporting at least 65535 colors with at least 128 Mbyte of memory.

NOTE:

Memory requirement is dependent on desired display resolution.

•

10,000 RPM (recommended) hard disk with a minimum of 1 GB available space.
A complete WinSpec/32 installation requires approximately 50 MB of space. The
remaining is required for data storage, and is dependent on the number and size of
images/spectra collected.

NOTE:

Disk level compression programs are not recommended.

•

Mouse or other pointing device.

«
...
28
29
30
31
32
...
»

Содержание NIRvana-LN



























































































































Отзывы:

Нет отзывов