Princeton Instruments NIRvana-LN Скачать руководство пользователя страница 31

Страница: 31 / 122

Chapter 4

System Setup

4.5 Data Acquisition Software Installation

This section provides the installation procedures for LightField and WinSpec/32 data
acquisition software.

4.5.1

Install LightField

Perform the following procedure to install LightField on the host computer:

NOTE:

Install the GigE Adapter card BEFORE installing the
WinSpec/32 application software.

The operating system on the desired host computer is either Windows Vista (64-bit) or
Windows 7 (64-bit).

Verify the Pro 1000 interface card has been installed.

Verify that the host computer is connected to the Internet. An internet connection may
be required for product activation.

Insert the LightField Installation CD into the CD drive on the host computer, and follow
the on-screen prompts.

Figure 4-1

illustrates a typical InstallShield Wizard dialog.

Figure 4-1: Typical LightField Installation Wizard Dialog

After the installation has been completed, reboot the host computer.

Connect the NIRvana-LN system components to the host computer and apply power.

Launch LightField and activate it according to on-screen instructions.

REFERENCES:

For additional information, refer to

Chapter 5, LightField First

Light Procedure

, on page 41.

Begin experiment configuration.

4411-

0145

_0016

Содержание NIRvana-LN



























































































































Результаты поиска

Содержание NIRvana-LN

Отзывы:

Princeton Instruments NIRvana-LN, Руководство пользователя, Страница: 31 / 122

Результаты поиска

Содержание NIRvana-LN

Отзывы: