Princeton Instruments NIRvana-LN Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 122

Princeton Instruments NIRvana-LN Скачать руководство пользователя страница 10

10

NIRvana

™

-LN System Manual

Issue 4

1.3 Document Organization

This manual is organized as follows:

•

Chapter 1, About this Manual

Briefly describes the NIRvana-LN family of detectors; details the structure of this
manual; and documents environmental, storage, and cleaning requirements.

•

Chapter 2, NIRvana-LN Camera System

Provides descriptions of each system component.

•

Chapter 3, Installation Overview

Cross-references system setup actions with the relevant manuals and/or manual
pages. It also contains system layout diagrams.

•

Chapter 4, System Setup

Provides detailed directions for mounting the detector to a spectrometer and for
interconnecting the system components.

•

Chapter 5, LightField First Light Procedure

This chapter provides a step-by-step procedure for placing a spectroscopy system in
operation for the first time when using Princeton Instruments’ LightField 64-bit data
acquisition software.

•

Chapter 6, WinSpec/32 and WinView/32 First Light Procedure

This chapter provides a step-by-step procedure for placing a spectroscopy system in
operation for the first time when using Princeton Instruments’ WinSpec/32 data
acquisition software.

•

Chapter 7, Exposure and Signal

This chapter discusses the various factors that affect the signal acquired on the
array, including array architecture, exposure time, temperature, and saturation.

•

Chapter 8, Experiment Synchronization

Discusses standard timing modes (i.e., Free Run, External Sync, and Continuous
Cleans,) Fast and Safe triggering modes, and TTL control.

•

Chapter 9, Non-Destructive Readout

This chapter provides information about Non-Destructive Readout, the ability to
read collected data without initiating a clean operation making it possible to
monitor an experiment’s progress without destroying/affecting currently collected
data.

•

Chapter 10, Troubleshooting

Provides courses of action to take if you should have problems with your system.

•

Appendix A, Specifications

Includes computer, controller and detector specifications.

•

Appendix B, Outline Drawings

Includes outline drawings of the NIRvana-LN detector and its power supply.

•

Appendix C, IsoPlane 320 Mounting

Provides mounting instructions for the spectrograph adapters available for
NIRvana-LN detectors.

«
...
8
9
10
11
12
...
»

Содержание NIRvana-LN



























































































































Отзывы:

Нет отзывов