background image

625-525revG-EN

9

Printed in USA 4/06 © 2006

Steamer

625-OS

Cleaning — Daily PM Tasks

Turn the unit off and unplug the power cord from the electrical 
receptacle. Proceed with caution, unit is still hot!

This unit is not watertight. Do not clean with a water jet/jet spray. Do 
not immerse the unit in water.

Do not use abrasive materials such as scrapers, steel wool, etc. to 
clean the spatula or steam chamber.

WARNING

CAUTION

While wearing protective gloves, remove the top cover by pulling 
up and off the unit.

1

Top Cover

A. Wash top cover, top plate, and venturi plate in a solution of 

McD

®

 APSC / APC made up in the back sink.

B. Rinse with clean water, and then sanitize in a solution of 

McD

®

Sink Pak Sanitizer.

C. Let air dry.

3

Use brushes to clean the water tube. Dip the brush in warm water 
or deliming solution. Insert the brush about 1" into water tube and 
then remove. Repeat for 30 seconds.

5

Insert Brush Here

The following tools are required:

McD

®

 All Purpose Super Concentrate (APSC)

McD

®

 Sink Pak Sanitizer McD

®

 APC

McD

®

 Delimer™

Clean sanitized towel

Protective (insulated) gloves

Steamer brush

16 oz (437 ml) cup

A. Remove spatula with 

insert.

B. Remove the top plate 

by carefully sliding it 
forward and out of the 
unit.

C. Remove the venturi 

plate.

While wearing protective gloves:

2

Top Plate

Venturi Plate

Spatula

Spatula Insert

OPTIONAL: If the surface shows 
signs of excessive calcium and 
lime buildup, dissolve two 
teaspoons (10 ml) of McD

®

 

Delimer™ in a small coffee cup 
with 100 mI of water. Pour half on 
each side.

Allow to sit for 5 minutes. Using a 
clean sanitized towel, thoroughly 
rinse and wipe the internal 
surfaces of the steam chamber.

4

Wipe the steam chamber surface with a clean sanitized cloth.

Wash all external surfaces of the steamer with a solution of McD® 
APSC / APC. Using the McD

®

 APSC / APC spray bottle, spray 

directly onto a clean sanitized towel and wipe the unit clean.

6

Do not spray directly on the unit or use abrasive cleaners!

Reassemble the unit.

Turn the unit on. When unit is preheated, run a minimum of four cycles to 
prime the unit and remove any residual cleaner.

CAUTION

Deliming

It is recommended that the steamers go through a deliming procedure at least once a month. Some hard water areas may require daily, 
weekly, or biweekly deliming based upon actual buildup.

Содержание 625-OS



















Отзывы: