Primera AP550e Скачать руководство пользователя страница 27

Страница: 27 / 32

AP550e Label Applicator 27

Container Platform

305 mm W x 310 mm D (12” W x 12.2” D) *

Container Height

9.5mm - 203mm (.002” - 8”) **

Container Shape

Flat, tapered front-to-back, flat front with rounded edges, cube,

cuboid, cylinder on end, prism on end

Label Width

19mm - 101,6mm (0.75” - 4”)

Label Height

19,mm - 152,4mm (0.75” - 6”)

Label Liner Width

22,2mm - 104,8mm (0.875” - 4.125”)

Label Placement

Leading edge up to 203mm (8”) from trailing container edge

Label Roll Diameter

203mm (8”) (maximum)

Label Roll Core

50.8 mm - 76.2 mm (2” - 3”) ID

Electrical Rating

12 VDC, 5.0 A

Power Requirements

100-240 VAC, 50/60 Hz, 1.7A

Agency Certifications

UL, UL-C, CE, FCC Class B

Weight

24 lbs [10.9 kg]

Dimensions

12” W x 21.3” D x 10.1”– 15.4” H [305 x 541 x 256 – 391 mm]

* Container may overhang platform to the front and/or either side.

** Containers shorter than 0.8” [20.3 mm] may require adaptive spacers. Some very short

containers may not be stiff enough to support label application.

Section 7: Specifications

Содержание AP550e
































Результаты поиска

Содержание AP550e

Отзывы:

Похожие инструкции для AP550e

Бренды по названию

Популярные бренды

Primera AP550e, Руководство оператора

Результаты поиска

Содержание AP550e

Отзывы:

Похожие инструкции для AP550e

Бренды по названию

Популярные бренды