Primera AP550e Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 32

background image

12 AP550e Label Applicator

2.2 Application Arm Height Adjustment

The Application Arm basically consists of the upper half of the applicator. This entire assembly

can be moved manually to four different positions to accommodate various container heights.

The maximum container height is 20 cm. There is no minimum height other than the height

required to make the container stiff enough for labeling.* To move from one position to

another, squeeze the Pin Release Bar to move the pin out of the notch. Move the Application

Arm up or down until the pin snaps into the desired notch.

Note:

When moving the Application Arm from one position to another, be sure to maintain upward

force at the front and rear of the arm. This will prevent the arm from falling when the Pin Release Bar is

squeezed and it will allow the arm to move more easily.

*

Containers less than 2 cm tall may require a riser to elevate the container above the back lip of

the platform. This will prevent the forward-moving platform from hitting the Application Arm.

Important!

Set the height of the Application Arm as low as possible without causing any part of the

arm, other than the Application Roller, to touch the container or platform at any time during the

application process. Keep in mind that the Application Roller is pliable and will flex during application.

Pin Release Bar

Pin

Position

Container Height

Notch 4

15-20 cm

Notch 3

10-15 cm

Notch 2

5-10 cm

Notch 1

0-5 cm

Application Roller and/or

label should touch container

first.

Container

«
...
10
11
12
13
14
...
»

Содержание AP550e

































Отзывы:

Нет отзывов

Похожие инструкции для AP550e

Saeco Poemia HD8325/08

Бренд: Saeco Страницы: 3

Бренд: 9BARISTA Страницы: 8

PROFESSIONAL BELGIAN IB08WR119

Бренд: Waring Страницы: 16

M2 Barsystem C10

Бренд: Cimbali Страницы: 2

Бренд: SEVERIN Страницы: 72

Horeca Large 380

Бренд: Rheavendors Group Страницы: 33

60-CUP COFFEE URN

Бренд: Hamilton Beach Страницы: 15

Бренд: ZORA Страницы: 36

Бренд: MACCHIAVALLEY Страницы: 30

Бренд: iDPRT Страницы: 12

Бренд: Hamilton Beach Страницы: 10

Бренд: B.F.C. Страницы: 32

Бренд: Westfalia Страницы: 50

Бренд: Hitachi Страницы: 32

Бренд: Frigidaire Страницы: 9

KCM514ER - JavaStudio Stainless-Steel Programmable Coffeemaker

Бренд: KitchenAid Страницы: 3

Бренд: KitchenAid Страницы: 32

JAVASTUDIO 4KCM511

Бренд: KitchenAid Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды