background image

Go-Go Elite Traveller Plus Technical Troubleshooting Guide

www.pridemobility.com

3

Table of Contents

INTRODUCTION ....................................................................................................... 4

SECTION 1: KEY INSERTED INTO KEY SWITCH - NO SIGNS OF POWER ....... 6

SECTION 2: KEY INSERTED INTO THE KEY SWITCH - POWER ON BUT
SCOOTER DOES NOT MOVE ............................................................................... 
10

SECTION 3: BEEP CODE DIAGNOSIS ................................................................. 11

BEEP CODE #3 - Battery Voltage is too High ..................................................................................11
BEEP CODE #5 - Brake Fault ..........................................................................................................11
BEEP CODE #6 - Throttle Trip .........................................................................................................12
BEEP CODE #7 - Throttle Trip .........................................................................................................12
BEEP CODE #8 - Motor Disconnected ............................................................................................14
BEEP CODE #9 - Possible Controller Trip .......................................................................................15

Содержание Go-Go Elite traveller




















Отзывы: