manualshive.com logo in svg

PRG Bad Boy Spot Luminaire, Руководство по обслуживанию

Прожектор PRG Bad Boy Spot Luminaire доступен для загрузки бесплатного сервисного руководства на нашем сайте. Скачайте его прямо сейчас, чтобы узнать как настроить и использовать этот мощный светильник. {Website} - ваш источник полезной информации для обслуживания и эксплуатации данного продукта.

Поделиться
Скачать
background image

BAD BOY

®

 SPOT LUMINAIRE FIELD SERVICE MANUAL

25

Pan/Tilt Issues

Tilt continues to move past center during calibration, and...
"TILT: no sensor" is displayed in Status Log and TLT sub-code is red

Details

: During initial Pan/Tilt calibration at power-up, Tilt will line up between the yoke legs and Pan will rotate looking for its 

mechanical stop. If Tilt continues to move past center, it is an indication that the COT sensor has failed or is unplugged from 
the Pan/Tilt Controller PCB. In addition, the Status Log will display error "TILT: no sensor" and the TLT sub-code will be red.

Solution

: Re-connect Pan/Tilt COT Sensor Cable.

Solution

: Replace Pan/Tilt COT Sensor... 

page 77

PAN sub-code is red and Status Log contains one or more Pan-related error codes, and/or...
TLT sub-code is red and Status Log contains one or more Tilt-related error codes

Details

: Upon power-up, the Pan/Tilt Controller PCB performs a calibration procedure that the Pan and Tilt must pass before 

allowing control of these two functions. The Tilt moves to a position between the two yoke legs and stops. The Pan rotates the 
yoke until it contacts the pan stop and reverses directions for half a turn then stops. The Status screen will show the PAN and 
TILT sub-codes in green if they pass. If the Pan/Tilt Controller PCB is faulty, or if either mechanism fails, the sub-codes will 
appear on the Status screen in red and there will be one or more entries in the Status Log containing an error message. 

Procedure

: Remove the Pan-Side Yoke Cover (

page 9

) and verify all connections to the Controller PCB are secure. If all 

connections are good, and the Pan and/or Tilt still fail, replace the Pan/Tilt Controller PCB with a tested "known-good" PCB. If 
the failures continue, follow up on the error codes to isolate the source of the failure. If the failures stop, replace the Pan/Tilt 
Controller PCB.

Solution

: Replace Pan/Tilt Controller PCB... 

page 76

Pan motor does not stop running after calibration, or...
"Pan Aux Encoder Fail" is displayed in Status Log and PAN sub-code is red

Details

: Upon power-up, the Pan moves all the way around to the pan stop and stops moving, then rotates 180 degrees and 

stops again. If it reaches the first stop and the pan motor continues to run, the Pan Drive Assembly has most likely failed. If 
upon power-up, the Pan calibrates and the Status Log displays "Pan Aux Encoder Fail," the Pan Drive Assembly’s auxiliary 
encoder has failed. 

Procedure

: Verify that all Pan and Tilt cables are properly connected to the Pan/Tilt Control PCB (

page 9

). It could save time by 

installing a known-good Pan/Tilt Control PCB to eliminate that component as a cause of the malfunction. If installing a good 
Pan/Tilt Control PCB does not fix the problem, the Pan Drive Assembly should be replaced.

Solution

: Replace Pan Drive Assembly... 

page 79

Tilt continues to move after it has reached center position between yoke legs during calibration, or...
"Tilt Aux Encoder Fail" is displayed in Status Log and TLT sub-code is red

Details

: Upon power-up, the Tilt will move to a position between the yoke legs and stop moving. If the Tilt continues to move 

after it has reached the center position between the yoke legs, the Tilt Drive Assembly has most likely failed. If upon power-up, 
the Tilt calibrates and the Status Log displays "Tilt Aux Encoder Fail," the Tilt Drive Assembly’s auxiliary encoder has failed. 

Procedure

: Verify that all Pan and Tilt cables are properly connected to the Pan/Tilt Control PCB (

page 9

). It could save time by 

installing a known-good Pan/Tilt Control PCB to eliminate that component as a cause of the malfunction. If installing a good 
Pan/Tilt Control PCB does not fix the problem, the Tilt Drive Assembly should be replaced.

Solution

: Replace Tilt Drive Assembly... 

page 82

Pan Drive or Tilt Drive Mechanism has no power

Details

: A 3 Amp Timed (Slo-Blow) Fuse protects the two drivers for the Pan/Tilt Controller PCB. 

Procedure

: If power is lost to either the Pan Drive or Tilt Drive Mechanisms, visibly check drivers for any damage. Verify all 

cables are properly installed. Replace the Pan/Tilt Controller PCB if any damage is detected. Inspect the cables to ensure they 
are not damaged or shorted. Replace any blown fuses and recalibrate the fixture. 

Solution

: Replace Pan/Tilt Controller PCB... 

page 76

Solution

: Replace 3A Fuse... 

page 69

Содержание Bad Boy Spot Luminaire




















































































































Отзывы:

Нет отзывов

Похожие инструкции для Bad Boy Spot Luminaire

THORLABS Vytran LFS4100 User Manual preview
Vytran LFS4100
Бренд: THORLABS Страницы: 44
Makita EM2650LH Instruction Manual preview
EM2650LH
Бренд: Makita Страницы: 84
NEC NEAX 2000 IVS System Manual preview
NEAX 2000 IVS
Бренд: NEC Страницы: 54
XAG P30 Quick Start Manual preview
P30
Бренд: XAG Страницы: 24
Abus JC9100 ERIC Assembly And Operating Instructions preview
JC9100 ERIC
Бренд: Abus Страницы: 2
Abus FUSG50110 Quick Manual preview
FUSG50110
Бренд: Abus Страницы: 12
Abu Garcia ZENON Manual preview
ZENON
Бренд: Abu Garcia Страницы: 6
AcceleDent aura Frequently Asked Questions preview
aura
Бренд: AcceleDent Страницы: 3
Zero 88 Solution Quick Start Manual preview
Solution
Бренд: Zero 88 Страницы: 32
IBS Scherer M-500 Translation Of The Original Instructions preview
M-500
Бренд: IBS Scherer Страницы: 64
Jasco UltraPro User Manual preview
UltraPro
Бренд: Jasco Страницы: 2
Nautilus 9NP-B7524 Series Owner'S Instructions preview
9NP-B7524 Series
Бренд: Nautilus Страницы: 2
Nautilus Be strong NS 700X Owner'S Manual preview
Be strong NS 700X
Бренд: Nautilus Страницы: 34
Nautilus BE STRONG E916 Quick Start Manual preview
BE STRONG E916
Бренд: Nautilus Страницы: 21
Raymarine ST70 Instrument Quick Reference Manual preview
ST70 Instrument
Бренд: Raymarine Страницы: 12
Raven SmarTrax Operation Manual preview
SmarTrax
Бренд: Raven Страницы: 73
Tascam DA-40 Tehnical Documentation preview
DA-40
Бренд: Tascam Страницы: 3
Safavieh Lighting Aurelia Quick Start Manual preview
Aurelia
Бренд: Safavieh Lighting Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды