Prestige Excellence Скачать руководство пользователя страница 74

Страница: 74 / 114

Maintenance Procedures

SECTION XVII- Maintenance

Procedures

Maintenance Procedures

The PRESTIGE Excellence should be

inspected and serviced annually, prefer-

ably at the start of the heating season, by

a qualified service technician. In addi-

tion, the maintenance and care of the

unit as outlined on page 66 and further

explained on pages 67 through 72 should

be performed to assure maximum effi-

ciency and reliability of the unit. Failure

to service and maintain the PRESTIGE

Excellence and the system components

could result in equipment failure, caus-

ing possible severe personal injury,

death or substantial property damage.

The following information provides

detailed instruction for completing the

maintenance items outline in the mainte-

nance schedule on page 66. In addition

to this maintenance, the PRESTIGE

Excellence should be serviced at the

beginning of the heating season by a

qualified service technician.

Reported Problems

Any problems reported by the owner should be

checked, verified and corrected before pro-

ceeding with any maintenance procedures.

Check Surrounding Area

Verify that the area surrounding the PRES-

TIGE Excellence is free of combustible / flam-

mable materials or flammable vapors or liq-

uids. Remove immediately if found.

Verify that combustion air inlet area is free of

any contaminates. Refer to the materials listed

on page 5 of this manual. If any of these prod-

ucts are in the area from which the unit takes

its combustion air, they must be removed

immediately or the combustion air intake must

be relocated to another area.

Inspect Burner Area

Remove the boiler front jacket panel and ven-

turi inlet elbow.
Vacuum any dirt or debris from the

burner/blower components.
Check the burner plate mounting nuts for tightness.
Check burner plate gasket for discoloration or

damage.
Re-install venturi inlet elbow and front jacket

panel when completed.

Do not use solvents to clean any of the

burner components. The components

could be damaged, resulting in unreli-

able or unsafe operation.

Check System Piping

Inspect all piping (water and gas) on the boiler

system for leaks and verify that the piping is

leak free and properly supported.
Inspect the fittings and components on the unit

and verify they are leak free.

Eliminate all boiler water system leaks.

Continual fresh make-up water will

reduce the heat exchanger life causing

boiler failure. Leaking water may also

cause severe property damage to the sur-

rounding area. Inspect the gas supply

piping using the procedure outlined on

Page 57.

NOTICE

WARNING

Содержание Excellence



















































































































Результаты поиска

Содержание Excellence

Отзывы:

Похожие инструкции для Excellence

Бренды по названию

Популярные бренды

Prestige Excellence, Руководство по установке и обслуживанию

Результаты поиска

Содержание Excellence

Отзывы:

Похожие инструкции для Excellence

Бренды по названию

Популярные бренды