Prestige Excellence Скачать руководство пользователя страница 22

Страница: 22 / 114

Boiler Piping

Boiler Return Connection

Boiler Drain Valve

(field supplied)

Boiler Supply

Connection

Pressure Relief Valve

(Supplied with Boiler)

3/4" Street Elbow

Air Vent

Drain Piping Directed

to a Suitable

Place of Drainage

Fig. 5: Pressure Relief Valve and Boiler Drain Valve Installation

Boiler Air Vent

This boiler is supplied with a special

automatic air vent that will provide reli-

able operation in purging air from the

boiler. The hygroscopic cap supplied

with the automatic air vent MUST

remain tight at all times on the air vent

body. The hygroscopic cap has a mem-

brane which expands upon contact with

water and seals the air vent until the

membrane dries up due to new air

forming in the air vent.

1. Make sure to fully tighten the cap on the air

vent on initial installation.

2. Never loosen the hygroscopic cap to allow

air to escape the air vent. Air will exit with

the cap fully tightened in place.

3. If the hygroscopic cap is not fully tight-

ened, water may leak from the cap. Simply

tighten the cap securely.

NOTICE

Содержание Excellence



















































































































Результаты поиска

Содержание Excellence

Отзывы:

Похожие инструкции для Excellence

Бренды по названию

Популярные бренды

Prestige Excellence, Руководство по установке и обслуживанию

Результаты поиска

Содержание Excellence

Отзывы:

Похожие инструкции для Excellence

Бренды по названию

Популярные бренды