Prestige Excellence Скачать руководство пользователя страница 11

Страница: 11 / 114

Pre-Installation Items

Recommended Clearances

The PRESTIGE Excellence is approved for

zero clearance to combustibles, excluding

vent and boiler piping.

- Boiler Piping - 1/4 inch from com-

bustible materials.

- Reference the appropriate vent supple-

ment for clearance requirements.

To provide serviceability to the unit it is

recommended that the following clear-

ances be maintained:
Top boiler jacket - 24 inches [610 mm].
Front  - 24 inches [610 mm].
Bottom boiler piping  - 24 inches [610 mm].
Rear - 0 inches
Sides  - 6 inches [153 mm]

If the clearances listed above cannot be

maintained or the enclosure in which the

boiler is installed is less than 85 cubic feet,

the space must be ventilated. See page 6

for ventilation requirements.

When maintaining zero clearance or less

than recommended clearances, some

product labeling may become hidden

and unreadable.

When installing the PRESTIGE

Excellence in a confined space, sufficient

air must be provided for proper combus-

tion and venting and to allow, under

normal operating conditions, proper air

flow around the product to maintain

ambient temperatures within safe limits

to comply with the National Fuel Gas

Code NFPA 54 - latest edition.

Residential Garage Installations

When installing the PRESTIGE Excellence in a

residential garage, the following special precau-

tions per NFPA 54/ANSI Z223.1 must be taken:

- Mount the unit a minimum 18 inches

[458 mm] above the floor level of the

garage. Ensure the burner and ignition

devices / controls are no less than 18

inches [458 mm] above the floor level.

- Locate or protect the unit in a manner so it

cannot be damaged by a moving vehicle.

Boiler Freeze Protection Feature

The Trimax boiler management system has a

freeze protection feature built in. This feature

monitors the boiler temperature and responds as

follows when no call for heat is present:

- 46ºF [8ºC] CH (1) & Auxiliary Boiler

Pumps ON

- 42ºF [6ºC] CH (1), Auxiliary Boiler &

System Pumps ON, Burner operates at

low fire

- 60ºF [15ºC] Freeze protection ends.

Burner & all pumps OFF after complet-

ing CH Post Pump Time.

The boiler freeze protection feature is

disabled during a hard lockout, however

the circulators will operate.

The boiler freeze protection feature is

designed to protect the boiler. The boiler

should be installed in a primary/sec-

ondary piping arrangement if it is

installed in an unheated space or

exposed to water temperatures of 46ºF or

less. See Section IV for primary/sec-

ondary piping examples. See Section X

for antifreeze guides.

NOTICE

WARNING

CAUTION

BEST PRACTICE

Содержание Excellence



















































































































Результаты поиска

Содержание Excellence

Отзывы:

Похожие инструкции для Excellence

Бренды по названию

Популярные бренды

Prestige Excellence, Руководство по установке и обслуживанию

Результаты поиска

Содержание Excellence

Отзывы:

Похожие инструкции для Excellence

Бренды по названию

Популярные бренды