Prestige 120 Скачать руководство пользователя страница 14

Страница: 14 / 48

EN • 14

ENGLISH

FRANCAIS

NEDERLANDS

ño

ALIAN

TSCH

664Y3300

INSTALLATIoN

chImney connectIon

- The chimney connections must comply with the NBN D51-003

standard and in accordance with current regulations.

- Thanks to its built-in gas/air ratio regulator, the

Prestige

is, to

a large extent, independent of pressure drops in the air intake

and flue-gas exhaust systems. However, the maximum pressure

drop of this system may not be exceeded; otherwise, the

pressure would diminish, and in the case of the Prestige 120,

the air pressure switch would lock out the boiler. However, the

gas/air ratio regulator always guarantees optimal combustion

with very low emissions.

- The horizontal flue gas exhaust ducts must be installed with a

sufficient degree of slope towards the boiler: 3° of slope = 5 mm

per meter of duct.

- There must be no obstructions or inlets to other appliances within

a radius of 0.5 meters around the terminal of the

Prestige

The maximum pressure drop of the chimney is 150 Pascal.

You can calculate this value using the following table:

(please see

sample calculation as well).

- The C33s configuration enables airtight operation in a

pre-existing chimney. The combustion air crosses the space

between the tubing and the pre-existing chimney. Make sure to

clean the pre-existing chimney thoroughly prior to installation,

especially if there is soot or tar residue. Make sure that there

is a clearance area for the combustion air at least equivalent to

the area that would have been provided by separate concentric

ducts or air intake ducts.

prestige

1000 mm

2000 mm

Sample calculation
Prestige Solo 50/75:

The diagram below consists of the
following  parts:  pipe  with  a  moni-
toring s 2 90° pipe bends
+  2  meters  of  horizontal  pipe  +
2  45°  pipe  bends  +  (2  +  1  +  1)
meters of vertical and sloped pipe
+ one vertical terminal unit.

The resistance of this system is
as follows:

3 + (2 x 12) + (2 x 6) +

(2 x 5,5) + (4 x 6) + 25 = 99 Pa.

As this value is lower
than the maximum
authorised resistance,
this installation is com-
pliant.

Table of chimney pressure drop in Pascal (1 Pascal

= 0.01 mbar)

Prestige Solo 50 - 75

Prestige Solo 120

Concentric pipe

Ø 100 / 150 mm

Separate

air inlet

Ø 100 mm

Separate

flue gas
exhaust

Ø 100 mm

Concentric pipe

Ø 100 / 150 mm

Separate

air inlet

Ø 100 mm

Separate

flue gas
exhaust

Ø 100 mm

Straight pipe 1 m

1,7

2,5

—

4,0

6,0

Pipe with monitoring

feature

—

1,3

—

3,0

90° bend

5,1

—

45° bend

5,5

2,1

—

5,4

8,0

Vertical terminal

—

Horizontal terminal

—

This table is based on ACV equipment and cannot be applied elsewhere.

Содержание 120

















































Результаты поиска

Содержание 120

Отзывы:

Похожие инструкции для 120

Бренды по названию

Популярные бренды

Prestige 120, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 120

Отзывы:

Похожие инструкции для 120

Бренды по названию

Популярные бренды