Prestige 120 Скачать руководство пользователя страница 41

Страница: 41 / 48

EN • 41

ENGLISH

FRANCAIS

NEDERLANDS

ño

ALIAN

TSCH

664Y3300

mCBA pARAmETERS FoR THE SpECIALIST

Codes

Description of the fault

Remedying the fault

Abnormal flame signal detected

- Check the wiring (short circuit in the 24V wiring)

- Check the electrode

- Replace the MCBA (water damage)

No flame presence signal after five start-up attempts

- Check the ignition wiring

- Check the electrode and its positioning

Check the gas supply to the burner

Gas valve or triac error

Replace the rectifier or the gas valve.

Persistant lockout

Press “RESET”

Internal error

If the problem persists after two “RESET” attempts,

replace the MCBA

EPROM error

If the problem persists after two “RESET” attempts,

replace the MCBA

Max input thermostat open or 24 V fuse has blown.

- Check the wiring

- Check the 24 Volt fuse of the MCBA

- Check link in 12-13.

Internal error

If the problem persists after two “RESET” attempts,

replace the MCBA

T1 > 110°C

- Check the NTC wiring and replace it if necessary

- If the NTC 1 sensor is OK, check if there is water flow

in the boiler

T2 > 110°C

- Check the NTC wiring and replace it if necessary

T1 gradient too high

- Check if the pump is running

- If there is no problem with the pump, bleed the system

No tachometer signal from the fan

- Check the PWM connection

- Check the fan’s wiring

If the problem persists after two “RESET” attempts,

replace the fan, otherwise, change the MCBA

The fan’s tachometer signal does not drop back

below “0”

- Check the draft in the chimney.

If the draft is sufficient, replace the fan

Short circuit NTC 1

- Check the connection of the NTC 1 sensor

- Check the wiring of the NTC 1 sensor

If the problem persists, replace the NTC 1 sensor

Short circuit NTC 2

- Check the connection of the NTC 2 sensor

- Check the wiring of the NTC 2 sensor

If the problem persists, replace the NTC 2 sensor

To unlock the system:

• Press “RESET” on the screen.

• If the fault reoccurs, contact your installer.

lIst of error codes + solutIons
[in error mode]

If a fault occurs during operation, the system locks down and
the screen starts flashing.
The first character is an “

” and the following two indicate the

code of this fault, as indicated in the table below.

Содержание 120

















































Результаты поиска

Содержание 120

Отзывы:

Похожие инструкции для 120

Бренды по названию

Популярные бренды

Prestige 120, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 120

Отзывы:

Похожие инструкции для 120

Бренды по названию

Популярные бренды