Precision matthews PM-1440GS Скачать руководство пользователя

Страница: 9 / 54

PM-1440GS v3 2020-10

Everyday precautions

• This machine is intended for use by experienced users familiar with metal-

working hazards.

• Untrained or unsupervised operators risk serious injury.

• Wear ANSI-approved full-face or eye protection at all times when using the

machine (everyday eyeglasses are not reliable protection against flying par

ticles).

• Wear proper apparel and non-slip footwear – be sure to prevent hair, clothing

or jewelry from becoming entangled in moving parts. Gloves – including tight-

fitting disposables – can be hazardous!

• Be sure the work area is properly lit.

• Never leave chuck keys, wrenches or other loose tools on the machine.

• Be sure the workpiece, toolholder(s) and machine ways are secure before

commencing operations.

• Use moderation:

light

cuts,

low

spindle speeds and

slow

table motion give

better, safer results than “hogging”.

• Don’t try to stop a moving spindle by hand – allow it to stop on its own.

• Disconnect 220 Vac power from the lathe before maintenance operations

such as oiling or adjustments.

• Maintain the machine with care – check lubrication and adjustments daily

before use.

• Clean the machine routinely – remove chips by brush or vacuum, not com-

pressed air (which can force debris into the ways).

No list of precautions can cover everything.

You cannot be too careful!

Содержание PM-1440GS



















































Результаты поиска

Содержание PM-1440GS

Отзывы:

Похожие инструкции для PM-1440GS

Бренды по названию

Популярные бренды

Precision matthews PM-1440GS, Руководство пользователя

Результаты поиска

Содержание PM-1440GS

Отзывы:

Похожие инструкции для PM-1440GS

Бренды по названию

Популярные бренды