Praxair PHOENIX 401 BASIC PULS forceArc Скачать руководство пользователя | Manualshive

Страница: 40 / 60

background image

Functional characteristics

MIG/MAG welding

40

Item No.: 099-004838-PRA01

5.2.6.3

Reset to factory settings
It is possible to reset all special parameters back to the factory settings.

Display

Operating
Element

Action Result

left right

Switch off the welding machine

-

-

VOLT

PROG

Press and hold button

-

-

Switch on the welding machine

t1

on

Switch welding machine off and back
on again to activate the changes

- -

5.2.6.4

Ramp time for wire creep (P1)
The wire creep begins with 1.0 m/min for 2 secs. Subsequently it is increased with a ramp function to 6.0
m/min. The ramp time can be set between two ranges.

5.2.6.5

Program "0", releasing the program block (P2)
The program P0 (Poti program) is blocked while shutting down with key switch. The operation is possible
only with P1...P15.

5.2.6.6

Display mode torch power control (P3)
The display of the torch power control shows program number or Up-Down setting in the normal
condition. It can be switched over to a blinking display. Then the program number and the welding type
(normal/pulse) are displayed alternately in the program operation. In Up-Down operation the Up-Down
settings and the Up-Down symbol are displayed alternately.

5.2.6.7

Program limit (P4)
The number of the absolute programs can be limited to above limit.

5.2.6.8

Special cycle in the operating modes special latched and non-latched (P5)
In the “normal” cycle of latched/non-latched the system starts with the start program Dvstart and
subsequently enters into the main program DV2.
In the “DV3 cycle” of latched/non-latched, the system starts with the start program Dvstart and
subsequently enters into the reduced main program DV3, remains there for the time T3 and then changes
automatically into the main program DV2. As a result an additional program is available in the cycle.

5.2.6.9

Enabling special JOBs SP1 to SP3 (P6)
This function is not available with machine control M3.71.
The JOB changeover is blocked if the key switch is in the “0” position.
This block can be cancelled for the special JOBs (SP1 - SP3).

«
...
38
39
40
41
42
...
»

Содержание PHOENIX 401 BASIC PULS forceArc





























































Отзывы:

Нет отзывов

Похожие инструкции для PHOENIX 401 BASIC PULS forceArc

TIG 160 DC Lift

Бренд: GYS Страницы: 20

EAGLE-GRIP 4 Series

Бренд: Easy Lift Equipment Страницы: 27

PORTAGANTRY 11000

Бренд: REID LIFTING Страницы: 21

Бренд: TCL Страницы: 48

Бренд: salmson Страницы: 195

Бренд: E2S Страницы: 12

Бренд: Fireside Audiobox Страницы: 12

MultiPRO Series

Бренд: Paton Страницы: 44

Бренд: ION Страницы: 48

Бренд: Miller Electric Страницы: 40

Бренд: Thermal Dynamics Страницы: 40

Trailblazer 251

Бренд: Miller Страницы: 48

Бренд: Lincoln Electric Страницы: 12

Transcmig 250se

Бренд: CIGWELD Страницы: 41

Bench Glo-Ring AH2711

Бренд: Eraser Страницы: 4

Robacta Reamer V 70 Han12P

Бренд: Fronius Страницы: 76

Бренд: weinor Страницы: 20

Бренд: Steren Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды