Form #44201150
-22- Sept
2010
9.2)
USER INSTRUCTION LABEL
The User Instruction label shown below is supplied with each heater. Affix this label adjacent to low level user
controls, such as thermostats, time clocks or control panels.
1. TURN ON GAS SUPPLY.
2. SET TIME SWITCHES OR THERMOSTATS TO DEMAND HEAT.
3.
SWITCH ON ELECTRICITY SUPPLY. RED & AMBER NEON INDICATOR ON.
4.
BURNER SHOULD IGNITE WITHIN 15 SECONDS, AMBER NEON INDICATOR ON.
5.
IF IGNITION IS NOT ACHIEVED DURING 12 SECOND IGNITION PERIOD LOCOUT OCCURS. THIS IS INDICATED BY THE AMBER NEON OFF. INTERUPT
ELECTRICITY SUPPLY TO APPLIANCE FOR 10 SECONDS TO RESET IGNITION CONTROL. IF A FIRST RESET IS NOT SUCCESSFUL, WAIT AT LEAST 15
SECONDS BEFORE REPEATING PROCEDURE. AFTER RESET, AN EXTENDED WAITING TIME WILL OCCUR.
6.
IF FLAME IS LOST DURING NORMAL RUNNING, THE AUTOMATIC IGNITION CONTROL WILL REPEAT START PROCEDURE AS AT 4 ABOVE.
7.
IF THE APPLIANCE FAILS TO IGNITE AFTER SECOND START SEQUENCE, SWITCH OFF ELECTRICITY SUPPLY TO APPLIANCE AND CALL SERVICE
ENGINEER.
8.
TO SHUT DOWN APPLIANCE, TURN OFF GAS AND ELECTRICITY SUPPLIES.
AFFIX THIS LABEL ADJACENT TO LOW LEVEL USER CONTROL.
OVERHEAD RADIANT HEATER OPERATING INSTRUCTIONS
4260440
Fig. 20
10.0)
TYPICAL HEATER ASSEMBLY
Sheet metal parts, particularly reflectors and vent have sharp
edges. Always use gloves when handling.
Failure to do so may result in death, serious injury or property
damage.
CUT HAZARD
See heater dimensions and assembly overview (Sections 7.0 through 8.1) for each U-model and Linear model
configurations.
During field assembly of the heater body sections, the recommended procedure is as follows:
1.
Determine the actual layout of the system first before hanging heater sections. Consideration must also be
taken for flue pipe, fresh air ducting, gas piping, clearances to combustibles, etc. before hanging heater.
2.
Install the heater suspension using chains or other type methods outlined in Section 9 “Typical Suspension
Methods”. Space these per the assembly overview for each heater.
3.
Space two (2) tube support/hanger brackets at distances indicated in each assembly overview for the first
tube section. Note: The distances are measured from center of the slotted holes of each support/hanger
bracket.
4.
Place tubes over these brackets with the welded seam facing down toward the ground. Failure to assemble
the tube with the seam facing down will void the manufacturer’s warranty. Secure the tubes to each
support/hanger bracket using U-bolt clamps and 5/16-18 nuts provided.
5.
Raise the tube section up to the suspension chain (or other methods), using “S” hooks to attach the tube
support brackets. Hang each tube section individually. DO NOT assemble all of the heater tube sections
together on the ground and attempt to hang the entire system. Provide a slope of 0.25 degree up to the fan
on linear tube heaters.
6.
Continue to pre-assemble and hang each additional section as before. Join each section together using
Torctite couplings as described in Section 10.1 “Tube Coupling Details”.
7.
Insert turbulators (where required) into the tube sections as shown in Section 10.2 “Inserting Turbulators”.
8.
Place U-bend (U-model heaters only) as shown in Section 10.3 “Attaching U-Bend”.
9.
Place main body reflector panels over each of the tube support/hanger brackets installed above.
10.
Attach burner box and fan assembly as shown in Sections 10.4 and 10.5 respectively.
Содержание PHS 25
Страница 52: ...Form 44201150 Sept 2010 51 1 3 4 2 5 7 7 6...
