PowerTec Digimax, Инструкция по установке и эксплуатации

Страница: 37 / 46

Page 29
DIGIMAX
® ® ® ® ®
Manual
ERROR CODE 02 -- ACCELERATION RAMP TIME TOO SMALL. ACCELERATION RAMP TIME TOO SMALL. ACCELERATION RAMP TIME TOO SMALL. ACCELERATION RAMP TIME TOO SMALL. ACCELERATION RAMP TIME TOO SMALL.
This error code comes up when a value is entered into parameter #6 which cannot be
achieved. Press ENTER to clear the error code and enter a larger value from 0.1 to 999.9.
ERROR CODE 03 -- DECELERATION RAMP TIME TOO SMALL. DECELERATION RAMP TIME TOO SMALL. DECELERATION RAMP TIME TOO SMALL. DECELERATION RAMP TIME TOO SMALL. DECELERATION RAMP TIME TOO SMALL.
This error code comes up when a value is entererd into parameter #7 which cannot be
achieved. Press ENTER to clear the error code and enter a value from 0.1 to 999.9.
ERROR CODE 04 -- VALUE GREATER THAN 255 VALUE GREATER THAN 255 VALUE GREATER THAN 255 VALUE GREATER THAN 255 VALUE GREATER THAN 255
This error may occur in entering parameters 12, #15, or #25. These parameters will not
accept a value greater than 255. Press ENTER to clear the error and reenter the value.
ERROR CODE 05 -- VALUE GREATER THAN 65535 VALUE GREATER THAN 65535 VALUE GREATER THAN 65535 VALUE GREATER THAN 65535 VALUE GREATER THAN 65535
This error may occur in the entry of parameter #1. The value of parameter #1 must be
between 0 and 65535. Press ENTER to clear the error code. Enter a correct value.
ERROR CODE 06 -- VALUE GREATER THAN 99999 VALUE GREATER THAN 99999 VALUE GREATER THAN 99999 VALUE GREATER THAN 99999 VALUE GREATER THAN 99999
This error may occur in any entry. Although you can't enter a number greater than
99999, for some reason the DIGIMAX
®
may think you did. Press ENTER to clear the error
and reenter the parameter.
ERROR CODE 07 -- ILLEGAL DECIMAL LOCATION ILLEGAL DECIMAL LOCATION ILLEGAL DECIMAL LOCATION ILLEGAL DECIMAL LOCATION ILLEGAL DECIMAL LOCATION
This error is generated if a number greater than 4 is entered into parameter #3. Press
ENTER to clear the error code and enter a number between 0 and 4.
ERROR CODE 08 -- ILLEGAL UNIT I.D. ILLEGAL UNIT I.D. ILLEGAL UNIT I.D. ILLEGAL UNIT I.D. ILLEGAL UNIT I.D.
This error code appears if a number 0 or a number greater than 255 is entered into
parameter #17.
ERROR CODE 09 -- ILLEGAL MODE VALUE ILLEGAL MODE VALUE ILLEGAL MODE VALUE ILLEGAL MODE VALUE ILLEGAL MODE VALUE
Parameter #8 and parameter #19 may have values of 0, 1, 2, or 3. Parameters #13,
#14, and #16 may have values of 0 or 1. Any other value will generate an error code 09.
ERROR CODE 10 -- ILLEGAL BAUD RATE ILLEGAL BAUD RATE ILLEGAL BAUD RATE ILLEGAL BAUD RATE ILLEGAL BAUD RATE
The baud rate for communications (parameter #18) must be one of those listed on page
19, or a special order value present in the software. Entering an incorrect value will generate
this error code.
ERROR CODE 11 -- ILLEGAL UP/DOWN INCREMENT VALUE ILLEGAL UP/DOWN INCREMENT VALUE ILLEGAL UP/DOWN INCREMENT VALUE ILLEGAL UP/DOWN INCREMENT VALUE ILLEGAL UP/DOWN INCREMENT VALUE
The value entered for parameters # 10 and #11 must be within the stated range.
ERROR CODE 12 -- 0 INTEGER NOT ALLOWED 0 INTEGER NOT ALLOWED 0 INTEGER NOT ALLOWED 0 INTEGER NOT ALLOWED 0 INTEGER NOT ALLOWED
Parameters #15 and #25 will not accept a zero input.
ERROR CODE 13 -- PARAMETER CHANGE NOT ALLOWED PARAMETER CHANGE NOT ALLOWED PARAMETER CHANGE NOT ALLOWED PARAMETER CHANGE NOT ALLOWED PARAMETER CHANGE NOT ALLOWED
If parameter #16 is set to 0, changes may not be made while in the run mode. Press
PGM/CLR to exit the parameter mode. Also, parameter #8 may not be changed while
running.
ERROR CODE 14 -- JUMP UP/DN VALUE TOO LARGE JUMP UP/DN VALUE TOO LARGE JUMP UP/DN VALUE TOO LARGE JUMP UP/DN VALUE TOO LARGE JUMP UP/DN VALUE TOO LARGE
The value of parameters #10 and #11 may not exceed parameter #1.