3
ASSEMBLY
Do not use the machine until it is completely assembled
and you have read and understood the entire operating
manuals.
TOOLS NEEDED
You will need the following tools to assemble and adjust
the machine. (The tools are not included.)
• 10mm Wrench
• 5 and 6mm Hex Wrenches
• Combination Square
• Phillips Screwdriver
MOUNT SANDER
• The machine must be installed in a well-lighted area
with correct power supply.
• The machine can be installed on either a workbench or
a tool stand by using bolts, lock washers, and hex nuts.
• The machine must be bolted to a firm and level surface.
• There must be enough clearance for the moving
workpiece during operation. There must be enough
room for safety operation of the machine.
ATTACH ABRASIVE DISC
Refer to Figure 2
• Remove all screws (b) and remove the Disc Cover (a).
• Clean the surface of the aluminum disc.
• Peel off the protective paper on the back of the Abrasive
Disc (c).
• With the adhesive side facing the aluminum disc,
carefully place the Abrasive Disc (c) onto the center of
aluminum disc.
• Confirm the position is satisfactory before pressing the
Abrasive Disc (c) firmly and evenly against the
aluminum disc in the entire area.
• Replace the Disc Cover (a) and tighten with screws (b).
ATTACH THE TABLE ASSEMBLY TO USE
WITH SANDING DISC
Refer to Figure 3
• Insert the Supporting Rod (d) into the mount on the side
of base (i), to the left lower corner of the Sanding Disc.
• Secure the Supporting Rod (d) onto the base (i) by
tightening the Bolt (l) against the flat surface of the
Supporting Rod (d). Check that Supporting Rod (d) is
stable and will not roll.
• Slide the Table Assembly (g) onto the Supporting Rod
(d) and position the table platform in level position.
• Adjust the distance between the table platform and
the Sanding Disc so it is 1/16” or less. Do not allow the
Sanding Disc to touch any part of the Table Assembly
(g).
• Secure the Table Assembly (g) in position with the Bolt
(h). Tighten the Bolt (h) against the flat surface of the
Supporting Rod (d). Check that Table Assembly (g) is
stable.
• Set the table 90 degrees (Perpendicular) to the Sanding
Disc with a Combination Square. Secure the table in
position by tightening the knob (j) on the tilt angle scale
under the table platform.
• Zero the angle indicator: set the pointer (k) to 0 degree.
ATTACH THE TABLE ASSEMBLY TO USE
WITH SANDING BELT
Refer to Figure 4
• With the Sanding Belt Assembly in upright position,
locate the Mount (e) of side of Sanding Belt Assembly.
• Insert the Support Rod (d) into the Mount (e). Secure
the Supporting Rod (d) onto the Mount (e) by tightening
the Bolt (f) against the flat surface of the Supporting Rod
(d). Check that Supporting Rod (d) is stable and will not
roll.
• Slide the Table Assembly (g) onto the Supporting Rod
(d) and position the table platform in level position.
• Adjust the distance between the table platform and the
Sanding Belt so it is 1/16” or less. Do not allow the
Sanding Belt to touch any part of the Table Assembly
(g).
• Secure the Table Assembly (g) in position with the Bolt
(h). Tighten the Bolt (h) against the flat surface of the
Supporting Rod (d). Check that Table Assembly (g) is
stable.
• Set the table 90 degrees (Perpendicular) to the Sanding
Belt with a Combination Square. Secure the table in
position by tightening the knob (j) on the tilt angle scale
under the table platform.
• Zero the angle indicator: set the pointer (k) to 0 degree.
WARNING
Figure 2
Figure 3
c
a
b
j
h
d
l
i
g
k
