background image

 

16 

 
 

1. Loosen the knobs on the chute deflector and adjust the 
chute deflector to the desired angle. 
2. Retighten the knobs. Do not over-tighten. 
 

 
 
 
 

 
OPERATING YOUR SNOW THROWER 

 

STARTING 

Please refer to ENGINE manual (separate document) for engine operation instructions. 
 

CLEARING SNOW 

 
Start the engine (see ENGINE manual) once your Snow Thrower has been running outside for several 
minutes, it is now ready for use. Make sure the path in front of your Snow Thrower is free from people, 
animals, objects, and all other obstructions except for snow. 
 
Adjust the chute outlet to the desired direction. 
Turn the chute rotation handle clockwise or counter-clockwise until the desired position is reached. 
 

WARNING!

 Never direct the chute outlet toward people or animals. While snow may seem harmless, it 

can contain rocks or other debris that can cause serious injury when projected through the chute. 
1. Engage/depress the auger control handle to start the augers and impeller turning. 
2. Set the desired direction and speed using the speed control lever. 
3. Engage/depress the drive control handle and direct the snow thrower into the snow to be cleared. 

NOTICE:

 Do not change speed positions while the drive is engaged. Disengage the drive control 

handle BEFORE changing speeds or directions. If the snow is deeper than the height of the auger, remove 
it in several steps taking narrower swaths. Make several passes with the auger overlapping the cleared 
areas and reduce forward speed. 
 
For the best clearing efficiency, clear snow before it melts, refreezes and hardens. Hard packed and wet 
snow can be very difficult to clear. 
 
Clearing wet heavy snow can be a challenge, depending on ambient temperature, humidity levels, and 
overall climate conditions including actual snow conditions, there may be no 100% solution as snow may 
be too wet or compacted to move or throw. Wet snow will tend to clog and stick more to the augers and 
chute. Keep the auger engaged as much as possible when clearing wet snow to help prevent clogging. 

 
WARNING!

 If snow is filled with foreign material, damage to the snow thrower may result. Avoid snow 

with foreign materials. 
 

 

Содержание DB7126PA

































Отзывы: