background image

 

24 

 

Problem 

Causes 

Remedy 

Drive system 

No forward or 
reverse drive 
movement when 
drive handle 
engaged 

Drive belt loose or damaged 

Check drive belt tension pulley for damage or 
incorrect tension, repair as necessary. Replace 
drive belt. 

Friction drive wheel is worn or damaged 

Replace friction drive wheel 

Friction drive wheel wet or slipping 

Allow snow blower to dry and or warm up or 
adjust drive cable tension as necessary 

Wheel to axle pins broken or missing 

Replace pins attaching wheels to axle 

Drive speed control 
stuck in gear or 
won’t change gears 

Speed control lever loose or damaged, not 
moving speed control cables 

Check speed control lever and cables for damage 
or loose or missing parts. Repair or replace parts as 
needed, ensure pivot stud spring tension is correct, 
adjust pivot nut spring tension as needed. 

Speed control cables loose, damaged or 
binding 

Repair, adjust or replace as necessary 

Drive speed control 
allows only 1 
direction  

Speed control cables misadjusted, loose, 
damaged or binding 

Check speed control lever and cables for damage 
or loose or missing parts. Repair or replace parts as 
needed. Adjust drive speed control cables, see 
Drive Speed Control Cables Adjustment 

Drive engaged 
when drive control 
handle released 

Drive control cable binding, won’t release 

Repair, replace cable as necessary 

Friction drive wheel return spring broke or 
missing 

Replace spring, adjust cable as necessary 

Auger System 

Auger not rotating 
when auger control 
handle engaged or 
Not blowing snow 
or Poor snow 
blowing 
performance 

Chute assembly clogged 

Clean chute and inside of auger housing with 
clean-out tool 

Auger shear pins broken 

Replace shear pins. Check each auger blade shear 
pin. 

Foreign object in auger or impeller causing 
auger to stop without shearing pins 

Remove object from auger or impeller areas 

Auger belt loose, slipping, worn or 
damaged 

Replace auger belt 

Auger belt tension cable loose, damaged or 
binding 

Repair, adjust or replace as necessary 

Auger blade(s) damaged or bent 

Replace auger blade(s) 

Auger gearbox mechanical damage, auger 
drive system not rotating freely (binding) 

Check bearings, bushings and all system parts for 
damage or mechanical binding. Repair or replace 
as necessary using proper lubrication 

Impeller damaged 

Replace impeller 

Impeller not connected to impeller shaft, 
impeller or shear pins broken 

Replace shear pins or impeller as necessary 

Forward speed too fast while blowing 
snow, overload 

Allow engine to maintain its speed. 

 

Содержание DB7126PA

































Отзывы: