PowerRiv HST-PR-LIGHT страница 32 Скачать руководство пользователя | Manualshive

Страница: 32 / 48

background image

- 32 -

6

7

8

Clean the chuck jaws (6) with a wire brush

and check for damage.

Lightly coat the chuck jaws with low-viscosity

oil, grease or Tefl on spray.

Please note: Do not clean the riveting tool

with fat solvents or water.

Also check the compression bushing (7) and

the compression spring (8) for damage.

Then reinstall the parts in reverse order.

Im Martelacker 12 – D-79588 Efringen-Kirchen – Telefon 0 76 28 - 91 11- 0 – Telefax 0 76 28 - 91 11-90

E-Mail: [email protected] – Internet: www.hs-technik.com

«
...
30
31
32
33
34
...
»

Содержание HST-PR-LIGHT

















































Отзывы:

Нет отзывов

Похожие инструкции для HST-PR-LIGHT

Бренд: Poltronova Страницы: 6

Бренд: EuroLite Страницы: 12

Бренд: RTRMAX Страницы: 21

SGG-Coach-FL1-C

Бренд: SolarGoesGreen Страницы: 2

Carlyle Tools WL2000UHL

Бренд: Napa Страницы: 13

Бренд: Gainsborough Страницы: 3

Бренд: Hoover Страницы: 2

Photographic 807726

Бренд: Habitat Страницы: 3

FOXFIELD PHEL5101BLK

Бренд: Park Harbor Страницы: 2

Бренд: MBT Страницы: 3

BAM TO-MD-017-060

Бренд: Balluff Страницы: 18

Бренд: Etlin-Daniels Страницы: 3

Бренд: Wetelux Страницы: 26

Бренд: Hamron Страницы: 28

Astral Extreme AS-X-400

Бренд: impact Страницы: 24

Бренд: Sycamore Страницы: 2

Бренд: CLD Страницы: 2

Бренд: Sharp Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды