Powermate LiftGate LG-3 Скачать руководство пользователя страница 40

Страница: 40 / 40



Inspect unit frames for structural damage.



Inspect frame hinge points. Apply LPS silicone lubricant (non-flammable)

if required.



Inspect all bolts and fasteners are in place and secure.



Inspect the load straps for damage. Nicks or tears are not acceptable.



Inspect the push button switch and rocker switch for condition and

operation. Make sure the wiring is secure.



Test the battery disconnect switch for operation. Cycle the unit testing for

operation, direction and smoothness.



Check that the toeplate is secure and not bent.



Observe the roller operation in the outer frame

rails. Oil rollers as required.



Ensure the operation manual is readily

available for reference.

PowerMate

LiftGate™ Installation & Operation Manual

DAILY MAINTENANCE SCHEDULE

FOR PARTS AND SERVICE CONTACT:

1-800-697-Mate

PN 018820 Rev.D2

Eng. 01/ 10/ 13

8.05

Содержание LiftGate LG-3









































Результаты поиска

Содержание LiftGate LG-3

Отзывы:

Похожие инструкции для LiftGate LG-3

Бренды по названию

Популярные бренды

Powermate LiftGate LG-3, Руководство по установке и эксплуатации

Результаты поиска

Содержание LiftGate LG-3

Отзывы:

Похожие инструкции для LiftGate LG-3

Бренды по названию

Популярные бренды