Powermate LiftGate LG-3 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 40

background image

PowerMate

®

LiftGate™

Installation & Operation Manual

MAINTAINING YOUR

PowerMate

®

LiftGate™

A properly maintained machine ensures trouble free and risk free operation. Regular
maintenance of your

PowerMate LiftGate

will ensure that it is always capable of

performing at peak efficiency resulting in less downtime caused by preventable repairs.

After every twenty-five hours of operation, ensure the following:

1. The Base Plate is securely anchored. Tighten Bolts if necessary.

2. Wire Looms at hinge points are not twisted or encumbered during swing out

movement.

3. Apply non-flammable silicone lubricant (EG. LPS) to hinge points. Wipe off

excess lubricant.

4. Check up/down operation of Unit. Drive mechanism should ratchet when Unit

reaches the retracted position. Drive motor should stop during extension

operation when the Toeplate makes contact with any surface.

5. Look for excessive movement between Inner and Outer Aluminum Frames.

6. Apply silicone lubricant (EG. LPS) to Top Urethane Rollers. Wipe off excess

oil.

7.

Check that Toe Plate is secure and not bent.

8. If Cylinder Attachment is installed:

- Check operation of Ratchet Tie Down Unit and Strap.

- Check to see if Eye-Bolt for Strap is bent indicating over tightening.

- Check to see if Strap is cut or frayed. If so, replace immediately.

If Aluminum Strapbar option is installed:

- Check to see if Strapbar Mounting Hardware is secure.

- Check to see if Load Binding Strap is cut or frayed. If so, replace

immediately.

- Check to see if Strap Locking Handle is secure.

9. Ensure Actuator Guard and Roller Guards are in place and secure.

10.

Ensure Mandatory Decals are in place.

After every twelve months, ensure the following:

1. Inspect complete assembly for wear and stress. Repair as required.

2. Inspect Actuator Clevis Mounts and Bolts for wear and stress. Replace

where necessary.

3. Check wiring integrity. Replace where necessary.

4.

Replace Mounting Hardware as required.

PN 018810 Rev.D2

Eng. 1/10/13

5.01

«
...
21
22
23
24
25
...
»

Содержание LiftGate LG-3









































Отзывы:

Нет отзывов

Похожие инструкции для LiftGate LG-3

Бренд: National Instruments Страницы: 8

Бренд: Balboa Страницы: 74

Бренд: cinetto Страницы: 56

Бренд: HIMA Страницы: 58

Бренд: WAGO Страницы: 20

Бренд: NCR Страницы: 12

Бренд: birddog Страницы: 30

Бренд: Vector Welding Страницы: 17

KPN235WEK-WELIK-DC

Бренд: Ravaglioli Страницы: 76

Бренд: Vestil Страницы: 6

Бренд: 2VV Страницы: 30

THERMASGARD 9112

Бренд: S+S Regeltechnik Страницы: 48

L2.00 AC/DC Expert 3.0 TIG

Бренд: EWM Страницы: 82

Бренд: Linde Страницы: 2

Бренд: Contec Страницы: 67

Бренд: WARPP Страницы: 11

Бренд: Solter Страницы: 16

Бренд: Delta Core Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды