background image

2

Fire and Burn Hazards

·

The exhaust system gets hot enough to ignite some materials.

  Keep  the  generator  at  least  1  meter  (3  feet)  away  from  buildings  and  other  equipment 

during operation.

 Do not enclose the generator in any structure.

 Keep flammable materials away from the generator.

·

The muffler becomes very hot during operation and remains hot for a while after stopping the 
engine. Be careful not to touch the muffler while it is hot. Let the engine cool before storing 
the generator indoors.

·

Gasoline is extremely flammable and is explosive under certain conditions. Do not smoke or 
allow flames or sparks where the generator is refueled or where gasoline is stored. Refuel in 
a well-ventilated area with the engine stopped.

·

Fuel vapors are extremely flammable and may ignite after the engine has started. Make sure 
that any spilled fuel has been wiped up before starting the generator.

·

Always  keep  fuel  away  from  sparks,  open  flames, pilot  lights,  heat  and  other  sources  of 
ignition.

·

DO NOT light or smoke cigarettes.

WAR

NI

NG:

When  use  the  LPG  generator,  if  find  any  problems(LPG  leakage  or  strange 

smells), please turn off the gas source immediately and then check the connection 
hose to insure the safely.

WARNING: 

1. When using the LPG/Gasoline generator, please be sure that there is at least 5 

feet  distance  between  LGP  tank  connecting  hose  and  the  generator,  to  prevent 
unnecessary danger because of high temperature surface of LGP tank.

2. When using the unit, please check the surface temperature of LPG tank.

3. Don't place the LPG tank in one place where ambient temperature above 35

and use LPG for electricity generating.

Содержание PD3G10000E
















































Отзывы: