background image

  

 
 
 

Owner’s Manual

 

 
 

 

 

 

Pressure Washer: Machine that cleans dirty surfaces with high pressure water

 

Instructions for Installation/Set-up, Operation, Maintenance, & Storage 

 

This pressure washer produces cold water high pressure spray.  Cleaning chemicals may be incorporated into the 
spray if desired.  The pressure pump for this equipment is powered by a gasoline internal combustion engine.  

 

WARNING: SPECIAL HAZARDS 

 

CO Poisoning:

 Exhaust from engine contains carbon monoxide, a poisonous gas that can cause carbon monoxide 

poisoning and possible death if inhaled. 

 

Injection Injury

: High-pressure spray can pierce skin and underlying tissues, leading to serious injury and possible 

amputation. Such an injection injury can result in blood poisoning and/or severe tissue damage. 

 

Flying Debris

: High-pressure spray can cause flying debris and possible surface damage. 

 

Electric shock

: Operating equipment in wet conditions or near water can cause electric shock. 

 

Chemical Exposure: 

Cleaning chemical vapors or contact with skin may be hazardous.

 

 

Fire/Explosion: 

Engine sparking can ignite fuel or other flammable liquids or vapors in the vicinity. Hot exhaust from engine 

can ignite combustible materials.  

 

Burns

: Pressure Washer pump and engine are hot surfaces that can cause burn injuries. 

Detailed safety

 

information about these hazards appears throughout this manual. 

Equipment Protection Quick Facts 

Inspect Upon Delivery:

 FIRST! Inspect for missing or damaged components. See 

“Initial Set-Up/Installation”

 section 

for where to report missing or damaged parts. 

 

Add Engine Oil:

 Engine is shipped 

without oil

. See the “Engine Manual” section of this manual for instructions on 

capacity and viscosity recommendations. 

Replace Temporary Pump Oil Plug: 

Pump is shipped 

with

 oil but with temporary shipping plug. Check pump oil 

level before starting and replace temporary shipping plug with permanent oil fill plug provided within plastic bag 
containing this Owners’s Manual. 

Water Flow Requirements:

 Make sure your supply water flow rate is 20% higher than the pressure washer's flow 

rate (see "Operations", section for detail), and that your water is clean and particle free. 

Chemical Spraying: 

Use only approved pressure washer chemicals designed for high-pressure use. Use soap 

adjustment knob to regulate cleaning power (on select units). 

Storage: 

Do not allow water to freeze in the pump, hose, or spray gun(s). See “Storage” for more information.  

Maintenance Schedule: 

Engine and pump require periodic inspection and servicing to keep pressure washer 

functioning efficiently. See “

Maintenance Schedule Summary

” for frequency of servicing.

  

Battery: 

 A battery is required for electric start feature (15771120 only).  A battery is not included. Purchase a 

standard 12 VDC, 10 Ah battery. Further detail in “Specifications” section. 

Any Questions, Comments, Problems, or Parts Orders 

Call Powerhorse Product Support 1-866-443-2576

 

ITEM NUMBER:  1577110, 15771120 
SERIAL NUMBER: _____________ 

M1577110E 

Содержание M1577110E































































Отзывы: