background image

Med Touch Series LCD Alarm Systems

Powerex  

  150 Production Drive  

  Harrison, OH  45030  

  USA

P   1.888.769.7979  

  F   513.367.3125  

  www.powerexinc.com

IN597400AV  

  08/2016

Page 56 of 56

(a) 

Powerex will not accept and shall have no responsibility for products returned without its prior written consent, and 

(b)

 Powerex will not 

assume any expense or liability for repairs to products made outside of its plant by third parties. In the event Powerex elects to replace a 

defective product, costs of installation, labor, service, and all other costs to replace the product shall be the responsibility of Buyer.

Powerex shall not, except as set forth above, be otherwise liable to Buyer or to any person who shall purchase from Buyer, or use, any products 

supplied hereunder for damages of any kind, including, but not limited to, indirect, special or consequential damages or loss of production of 

loss of profits resulting from any cause whatsoever, including, but not limited to, any delay, act, error or omission of Powerex. Supplier’s repair 

or replacement of any Product shall not extend the period of any warranty of any Product.

Warranty Disclaimer.

 Powerex has made a diligent effort to illustrate and describe the Products in its literature, including its Price Book, 

accurately; however, such illustrations and descriptions are for the sole purpose of identification, and do not express or imply a warranty that 

the Products are merchantable, or fit for a particular purpose, or that the Products will necessarily conform to the illustrations or descriptions.

Product  Suitability.

  Many  jurisdictions  have  codes  and  regulations  governing  sales,  construction,  installation,  and/or  use  of  Products  for 

certain purposes, which may vary from those in neighboring areas. While Powerex attempts to assure that its Products comply with such codes, 

it cannot guarantee compliance, and cannot be responsible for how the product is installed or used. Before purchase and use of a Product, 

please review the Product applications, and national and local codes and regulations, and be sure that the Product, installation, and use will 

comply with them.

Claims.

 Any non-warranty claims pertaining to the Products must be filed with Powerex within (6) months of the invoice date, or they will not 

be honored. Prices, discounts, and terms are subject to change without notice or as stipulated in specific Product quotations.  Powerex shall not 

be liable for any delay or failure arising out of acts of the public enemy, fire, flood, or any disaster, labor trouble, riot or disorder, delay in the 

supply of materials or any other cause, whether similar or dissimilar, beyond the control of Company.  All shipments are carefully inspected and 

counted before leaving the factory.  Please inspect carefully any receipt of Products noting any discrepancy or damage on the carrier’s freight bill 

at the time of delivery.  Discrepancies or damage which obviously occurred in transit are the carrier’s responsibility and related claims should be 

made promptly directly to the carrier.  Returned Products will not be accepted without prior written authorization by Powerex and deductions 

from invoices for shortage or damage claims will not be allowed.  

UNLESS OTHERWISE AGREED TO IN WRITING, THE TERMS AND CONDITIONS 

CONTAINED IN THIS LIMITED WARRANTY WILL CONTROL IN ANY TRANSACTION WITH POWEREX.

  Any different or conflicting terms as may 

appear on any order form now or later submitted by the buyer will not control.  All orders are subject to acceptance by Powerex.

Содержание Med Touch Series

























































Отзывы: