background image

 © 2014-2015 Minuteman International, Inc.

Nautilus Hi-Dump Rider Scrubber/Sweeper  #988752UM  Rev. * 03/16

Page  28

MACHINE OPERATION

HOPPER HIGH DUMP SWITCHES

The three high dump switches are 
located on the left side of the 
operator compartment.

BUMPER RAISE/LOWER SWITCH

The left switch is the bumper raise/lower switch. Pressing 
and holding the top of the switch raises the bumper. Pressing 
and holding the bottom of the switch lowers the bumper. The 
lift can be stopped at any height by releasing the switch.

HOPPER RAISE/LOWER SWITCH

The center switch is the hopper lift raise/lower switch. Press-
ing and holding the top of the switch raises the hopper. 
Pressing and holding the bottom of the switch lowers the 
hopper. The hopper can be stopped at any height by releas-
ing the switch. 

HOPPER DUMP DOOR SWITCH

The right switch is the hopper dump door switch. The hopper 
dump door is automatically held in the open position when 
scrubbing and is automatically closed when the hopper is 
raised for dumping. Momentarily pressing the top of the 
switch opens the hopper dump door. It is not necessary to 
hold the switch in the open position.

Содержание Nautilus CE PB45HDSLCE







































































































Отзывы: